Question about 1992 Chevrolet S-10

1 Answer

I have a 92 chevy S10 truck, how do you remove the wiper blades and arms?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

GM S10/S15/Sonoma Pick-Ups 1982-1993 Repair Manual Blade and Arm - REMOVAL & INSTALLATION
(see Figures 1, 2 and 3)

  1. Matchmark the base of the wiper arm to the linkage. This will assure the arm is installed in the proper position. If the arm is being replaced, transfer the matchmark from the old component to the new one before installation. This can be done by placing the new arm on top of the old one and copying the mark.
I have a 92 chevy S10 truck, how do you remove the - 1bb2352.jpg

Fig. 1: Removing the wiper arm using J-8966

0234572.jpg

Fig. 2: If no wiper arm tool is available, use a small prytool I have a 92 chevy S10 truck, how do you remove the - 5227e24.jpgthe spring

5227e24.jpg

Fig. 3: With the spring released, pull the wiper arm from the linkage
  1. Most wiper arms are retained by a spring clip. Some are equipped with a release tab at the center which should be depressed to release the arm. If no tab is provided, use a small prybar or a wiper arm removal tool such as J-8966 to depress the spring and release the arm. Remove the arm from the vehicle.
  2. Some late model vehicles (all 1993 and some earlier models) are equipped with a wiper arm that utilizes a small release hole at the base of the wiper arm. If equipped, insert a 1 / 8 in. drift pin into the tool access hole to release the locking device and allow the arm to be easily pulled from the transmission. If necessary, use a gentle rocking motion to remove the arm.
To install:
  1. Except for late model vehicles equipped with the tool access hole, align the matchmarks and gently press the blade over the linkage and snap into position.
  2. For 1993 vehicles (and earlier models equipped with the access hole on the arm) straighten the arm assembly and insert the pin. Align the arm with the linkage mark made earlier, then press down on the arm's head casting until it seats and locks onto the wiper pin. Remove the drift pin.
  3. Operate the wipers and verify proper alignment.

Hope helps (remember rated this).

Posted on Jul 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to change wiper blades on 2006 trailblazer. i can't get the wipers off.


The 2006 Chevrolet Trailblazer has the most common hook-end wiper arms. Purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

2006 Chevy Trailblazer Wiper Blade Installation Videos (hook end arms)

2006 Chevrolet Trailblazer Wiper Blade Size Options w/Correct Lengths & Attachments

Aug 16, 2011 | 2006 Chevrolet Trailblazer Ext

1 Answer

How do I change wiper blades 2001 Chevy blazer


Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage.
Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pQJ39h
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pJlPaV
  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

    Jan 15, 2011 | 2001 Chevrolet Blazer

    1 Answer

    I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


    Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
    1. Turn ignition switch to ACCY position.
    2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
    3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
    To Install:
    1. Insert wiper arm hook through opening in wiper blade.
    2. Place wiper blade pivot in the inside radius of wiper arm hook.
    3. Pull on wiper blade pivot into hook until it locks into place.
    4. Check wipers for proper operation.
    Wiper Arm To Remove:
    NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
    1. Remove washer hose.
    2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
    3. Remove wiper arm from shaft.
    To Install:
    1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
    2. Press arm assembly on shaft and push retaining latch IN.
    3. Connect washer hose.
    4. Remove windshield markings and check wipers for proper operation.
    prev.gif next.gif

    Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

    1 Answer

    How do I change my wiper blades on my '92 Crown Vic? Do I have to change the whole wiper arm?


    Most auto parts stores will gladly change out the blades for you. As far as your question.......No, you only have to replace the blades and not the completer wiper arm.
    Hope this helps

    Aug 26, 2010 | 1992 Ford Crown Victoria

    1 Answer

    I need to know how to remove a 1987 chevy s10's windshield wiper, not the arm but just the wiper. cant find a release switch and am thinking i need to force it off


    Use a small screwdriverslide it between the plastic of the wiper blade and the top of the wiper arm. There is a tab that holds the blade in place, you should be able to gently pull the wiper back off the arm.

    May 03, 2010 | 1987 Chevrolet S-10 Pickup

    1 Answer

    How do you remove the windshield wiper arms


    The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

    Apr 07, 2010 | 1987 Chevrolet S-10 Pickup

    2 Answers

    How install wiper blades on 96 chevy corsica. i can't get the old ones off. so more preciesly, how do you get the old ones off?


    you should have "pin" type wiper arms on it. that means there are short, maybe 3/16 inch diameter pins that the wiper blades mount and pivot on. get a screw driver and where the pin goes through the wiper blade there will be a little plastic tab or lever that needs to be depressed and held down while you slide the wiper off of the pin on the wiper arm. pivoting back and forth with the wiper will help in removing it.

    Nov 06, 2009 | 1996 Chevrolet Corsica

    1 Answer

    Remove and replace wiper blade assebly 89 chevy silverado


    there is a keeper on the inside of the arm. its easier to get to if you remove the whole arm. lift the wiper arm and near the pivot point there is a little flat bar that sticks out along the arm itself. its about a quarter inch long. pull that out alittle and slide the arm off the peg. makes it easier for me. if you cannot get the wiper off still, destroy it. your replacing it anyway and the arm is pretty sturdy.

    Jun 03, 2009 | 1989 Chevrolet K1500

    1 Answer

    1984 chevy S10 windshild wipers


    at the arm remove the cap on end and their is a nut remove it 10 mm / Please rate my response thank you very much

    Jan 28, 2009 | 1984 Chevrolet S-10

    1 Answer

    Wipers seized- motor works. cant move blades more tham1=2 inches.


    you have to remove the whole wiper arm both sides...under hood remove 5 -5/16 screw from vent panel .. remove panel .. under panel on drivers side you will see where arm attach to wiper motor ..remove nut... then remove 3 bolts that hold wiper motor to firewall .

    Nov 29, 2008 | 1988 Chevrolet S-10

    Not finding what you are looking for?
    1992 Chevrolet S-10 Logo

    2,043 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8531 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...