Question about 1998 Chevrolet Blazer

2 Answers

I'm trying to remove my driver's side door panel to troubleshoot my power window (I can hear the motor running, but it won't lower). I'm guessing that the window is no longer on its tracks. The book isn't very clear on how to remove the panels, though, and I'm getting stuck. Would really appreciate some advice :) !!!

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Posted on Jul 20, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 343 Answers

Remove the screws that should be on the bottom of the door panel and there should be one on the door handle or armrest or both. Pop out the window switch and release the connector and do the same for the door lock switch. Remove the switches. Pull the panel from the bottom toward you with a quick tug and you should hear a couple of the clips pop out from the door. Make sure to pop all of them out around the perimeter of the panel and then from the bottom of the panel, push up towards the sky and it should come free. To reinstall, reverse the steps and once the panel clips are aligned with the holes on the door, use your palm and hit the panel on the edges to secure the clips. Please rate me on my answer.

Posted on Jul 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford expedition drivers side window won't roll up


well windows are usually pretty simple. It could be the window switch, the regulator bound up, or the motor itself went out. try jiggling the switch, actuate the switch over and over..see if you get any movement. sometimes smacking the side panel will jolt the motor. If that doesn't work i usually take off the door panel, try supplying the motor power, if that works that tells me the switch is bad. if the motor doesnt do anything even with 12volts supplied, then that tells us the motor is bad. if you hear the motor work but its grinding and nothing happens, the regulator is bad. Let me know if you have questions, i can help you further

Jun 11, 2013 | Cars & Trucks

1 Answer

Drivers side power window doesn't work. The other windows work fine. I need a wiring diagram When I try to lower the window I hear a click coming from the drivers door module. any help will be appreciated


you will need to remove the panel and have a look as it could be the motor cables have jammed and this is why you can only hear a click ,so have a good look then if need be answer this post and we can go from their

Mar 08, 2011 | 2000 Buick LeSabre

1 Answer

2005 Chrysler T&C passenger side window went down and won't come up. All other automatic windows and door locks work fine - don't hear any motor sound / buzz / etc. when either driver side or passenger...


If the window had not been slow in it's action before it stopped working I'm guessing you only have a connection problem. I would remove the door panel and using a multimeter check the hot wire to see if power is reaching the switch. If it is check the connection on the motor. If power is reaching the motor through the switch you have a faulty motor. If at any point of testing there is no power backtrack the power wire to find where the break is. (it's usually in the door jam)

Apr 13, 2010 | 2005 Chrysler Town & Country

2 Answers

My driver side window won't roll down, it is a


if only one window has the problem then it is not a fuse or circuit breaker, most likely the window motor is defective.

Sep 19, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

My driver side power window doesn't work.


Removing a door panel is easy. First locate all of the screws and remove them, some will be hidden under plastic covers. Next take a door panel tool (about $5.00 at a parts store) work it around the panel to find the plastic keepers, carefully pop out the keepers, the keepers will need to be replaced just try not to damage the panel, you can buy need keepers at part stores or even hardware stores.

Jul 22, 2009 | 2004 Ford F150

3 Answers

Power window on driver side door sticks


Yes the door's rubber window guide becomes dry and needs to be lubricated with a special silicone lubricant, go to Napa and ask for this silicone lube then apply it to the grooves located around the inner perimiter of the door window frame, sometimes it is neccessary to remove the door panel to access the lower window guides, if you remove the door panel becareful when removing clips along the lower part of panel you can damage the panel using a screw driver the sell a tool for this it looks like a screwdriver with a Y shape at the end. If this doesn't remidy the problem you more than likely have a worn out window motor that needs replacement.

Jul 02, 2009 | 1995 Volvo 850

3 Answers

Power window


if you can hear the motor humming or running chances are that your window is off track an jammed or the motor s just humming an has no power to bring the window up, driver side window is the first one to go out because it gets more use of than all the other windows. the ony better way to find out is to remove the door panel an make sure you use the right tool to remove the plastics studs , because you don't want to bust the plastic studs behind the door panel.

May 27, 2009 | 2001 Chevrolet Blazer

1 Answer

Rear driver side power window will not work


I'm guessing you've removed the door panel since you said you removed the switch. but just in case...you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. Then pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything.It sounds like the motor may have died you on if you cannot hear it...it could also be the regulator or linkage has broken

Apr 10, 2009 | 1999 Buick Century

1 Answer

Driver side power window motor not functioning


It is the motor. Remove the inner door panel. Lower the window and remove the glass. 2 10mm nuts and window will lift out. Winow has to be in postion where you can reach the nuts through port holds in door. Knock out the center pins on the rivets holding the motor in. Unplug motor. Drill out the rivets and remove the motor. Replace motor and re rivet or screw it back in with bolts, nuts and loc tight. replace window and door panel and you are done. the charge for someone who does this all the time is 1.5 hours labor.

Mar 21, 2009 | 1998 Chevrolet Cavalier

1 Answer

My 2003 Forester driver side window wont work.


You need power window regulator as the cable of the regulator is out its place ,

  1. Remove the gusset cover.
  2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
  3. Remove the power window switch assembly.
  4. Using a trim panel remover, remove the clips of the trim panel.
  5. Remove the speaker.
  6. Using a spatula, remove the door sealer.
  7. Remove the outer mirror assembly.
  8. Remove the front end of the door weatherstrip and gusset.
  9. Remove the stabilizers.
  10. Remove the rear end of the door weatherstrip (inner and outer).
  11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
  12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
  13. Loosen the nuts to remove the rear sash.
  14. Disconnect the power window motor wiring harness.
  15. Loosen the four bolts and two nuts to pull out the regulator assembly.
  16. Remove the screws to remove the motor from the regulator assembly.
  17. Installation is the reverse order of removal.0759a6d.jpg23cb1e4.jpg

Good luck...

Oct 21, 2008 | 2001 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...