Question about 1994 Ford Ranger Supercab

1 Answer

I bought a 1994 ranger for my grandsons first vehicle ,but the a/c doesnot seem to cool,although the pressures look good ,does this trucks drier have a eri valve in the drier.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,857 Answers

Rather than tell us something looks good you need to tell us the pressures for us to even begin.

Posted on Jul 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble shoot turn signals 1994 Ford Ranger 2.3 engine


Diane, There are 2 separate flashers on your vehicle, one is for the emergency/4 way lights and one flasher is for the signal lights. It may be worth the couple bucks and replacing the signal flasher as a first step. Recheck bulbs/sockets, fuses/relays, flasher. If all looks good possible signal switch is bad. Remove switch and try to clean contacts or replace switch. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://ca.answers.yahoo.com/question/index?qid=20090405174036AARb2Uc
1994 Ford Ranger Turn Signal Electrical Problem 1994 Ford Ranger
93 Ranger Turn Signal Problem Ford Truck Enthusiasts Forums

Aug 20, 2016 | 1994 Ford Ranger Supercab

1 Answer

1994 Ford Ranger low power


Ok, it sounds as though your fuel pressure regulator or injector lines or injectors are leaking. What engine is in the vehicle? Is the engine light flashing? Does it start hard and blow smoke on startup?

May 31, 2014 | 1994 Ford Ranger Supercab

1 Answer

1994 olds cutlass ciera air conditioning low pressure sensor


The low pressure cycle switch is located under the air filter housing. It is attached to the accumulator drier. the drier is a canister with two aluminum lines and this sensor attached to it .

Aug 06, 2012 | Cars & Trucks

1 Answer

1994 ford ranger ran ot of gas now won't start. Put fuel in it made sure saftey switch (reset switch) was okay. But still wont start. Fuel pump seems to be working. Any suggestions ...


Do you know what the fuel pressure is at?

Try this. While somebody cranks the engine over whack the bottom of the fuel tank (about dead center) with a rubber mallet. If the vehicle starts replace the pump. The fuel pump is kept cool by the fuel in the tank. Running the tank dry is hard on the fuel pump.

May 04, 2011 | 1994 Ford Ranger Supercab

1 Answer

Where is the low side port for the 1990 ford ranger


1990 Ford Ranger was equipped with an R-12 system (Unless it has been retrofitted) The low side port for those systems were usually on the suction-side reciever/drier. I have also seen upgraded hose kits installed on some of these vehicles (for retrofitting purposes) where the port is on the hose assembly between the drier and the compressor or even on the compressor manifold itself.

Apr 08, 2011 | Ford Ranger Cars & Trucks

3 Answers

1994 ranger 2.3L 5 speed, 2WD, a/c. Cranks but


connect fuel pressure gauge see what pressure you have with key on reply back

Feb 04, 2010 | Ford Ranger Cars & Trucks

4 Answers

No clutch pedal been bleeding it for 3 days. i have replaced the slave cylinder, clutch and clutch master cylinder. its a 1994 ford ranger 2.3L 5speed


On a Ford Ranger you need to have the clutch master cylinder facing up when you are looking at it mounted on the vechile it is pointing down you need to have it facing up and also have a bleeding tool I went out and bought a POhoenix Injector which makes it real easy and you can do it buy your self. Good luck

Dec 06, 2009 | 1994 Ford Ranger Supercab

1 Answer

1994 ford ranger. won't start, good spark,fires,


could be many things , but fuel and fire are a good sign. check the ESC, and that you have a full 12vdc in the vehicle, then check that all cyl have fire, poss bad coil pack

Oct 04, 2009 | 1995 Ford Explorer

1 Answer

Oil in coolant only


You might have a blown head gasket that is allowing one of your oil galleries in the engine to mix engine oil with the coolant after the oil pressure gets to a certain point. You might also have a cracked head causing the same type of problem.

Nov 11, 2008 | 1983 Ford Ranger

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...