Question about 2001 Jeep Cherokee

1 Answer

Brake light stay on all time disconnect brake light switch still stay on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Any short there or any ground, check wires and harnesess

Posted on Jul 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake light on dash coming on and off now on all the time plenty brake fluid good pedal stops ok e brake off


Year/make/model?? Try disconnecting the electrical connector at the master cylinder to see if the light goes out. If it does, suspect a float issue in the reservoir. If light stays on, disconnect plug at park brake to see if it goes out. If it does, suspect park brake switch issue

Oct 25, 2015 | Cars & Trucks

3 Answers

Why do the brake lights stay on after the brake switch is disconnected?


be sure that brake pedal is all the way up even if you have to pull it up or thers a wire shorted

Oct 15, 2014 | Cars & Trucks

1 Answer

1974 VB Bug, brake lights are ON when car is on...stay on when breaks are applied (so virtually driving without break lights as they are always on!


If you look underneath your bug on the driver's side where the master cylinder is you will see 2 electrical plugs plugged into the master cylinder. Each plug has 3 wires. Disconnect both from the master cylinder and see if the brake lights go out. If so, then replace both brake light switches on the master cylinder. You can disconnect one at a time and see if the lights go out that way. Which ever one that causes the lights to go out when disconnected is the bad switch. The light circuit will work with only one switch connected, so if neccessary you can get by on one switch.

Sep 14, 2013 | 2000 Volkswagen Beetle

1 Answer

Brakes light stays on all the time-even with the brake light switch disconnected


Since brake lights are normally supplied with chassis ground through the switch, the wire leaving the switch is grounded somewhere between the switch and the point at which the wire branches to left and right. The problem may be in a cable bundle and not even visible.

Mar 24, 2011 | 1994 Nissan Altima

1 Answer

Brake lights stay on all the time . Checked brake pedal switch and it closes and opens as per reading on ohm metter, brake lights continue to stay on even when I short out brake switch connector.


This is the diagram. If you disconnect the switch, do they stay on? If so, you have another circuit feeding it (i.e. new radio or alarm installed maybe?)

0900c15280265691.gif

Dec 19, 2010 | 1995 Nissan Altima

2 Answers

Brake light stays on


the switch for your brake lights is located near your brake pedal,it is usually a spring loaded switch that comes out when the pedal is pushed & the pedal pushes it back in when it is released,this switch may have come loose & is active all the time,you need to make sure that it is pushed hard up against the brake pedal & tighten the adjusting screws to lock it in position,check that your stop lights come on when the brake pedal is pushed in....hope this helps....cheers

Jul 09, 2010 | 1997 Nissan Pickup

2 Answers

Tail Lights stay on all the time.


under the dashboard on the drivers side. look at the brake pedal lever. there should be a switch attached. push switch in and twist to remove. then pull the button as far out as it will go. while holding brake pedal down reinstall switch. then pull pedal up to top. this will reset the brake light switch. if they stay on still, then just replace the brake light switch.

Jan 19, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Brake and/or taillights stay on


First, check the brake light switch, and if the high level light is on, the brake light switch is the likely problem. Even if it isn't, the bulbs could be burnt out. Anyway, disconnect the wire harness from the brake light switch on the brake pedal. If the lights go out, replace the switch. To test the light switch, disconnect the wire harness from that (with the switch in the "off" position). Again, if the lights go out, this is the problem. More likely, it is the brake one. This happened on my Dodge twice.

Dec 25, 2008 | 1998 GMC Jimmy

2 Answers

Voyager tail lights stay on


brake light switch or a headlight switch

Nov 11, 2008 | 1995 Plymouth Voyager

Not finding what you are looking for?
2001 Jeep Cherokee Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...