Question about 1992 Chevrolet C1500

1 Answer

PUT NEW BRAKE CALIBER ON MY TRUCK AND IT IS STILL STAYING STUCK

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Ok, if you change the caliper and it still stays stuck, then a proportioning valve or master cylinder may be stuck or there is a
constriction in the hydraulic line.

Maybe replace the lines to the othe rparts of the braking system.

Posted on Jul 08, 2010

Testimonial: "it was a bad brake line thanks for the help"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gear shifter stuck in park on 2008 dodge caliber


the brake light switch control the shifter. replace the brake light switch.

Apr 04, 2014 | 2008 Dodge Caliber

1 Answer

1994 Chevy Cavalier front right brake is locking up every time you step on brake . I already changed that caliber and it is still doing it


MOST OF THE TIME WHEN A CALIBER LOCKS UP: IT IS NOT BECAUSE OF THE CALIBER BEING BAD. THE CAUSE IS THE RUBBER BRAKE LINE GOING TO THE CALIBER IS BAD INSIDE OF THE RUBBER HOSE. ONCE YOU PRESS THE BRAKE PEDAL YOU PUSH FLUID INTO THE CALIBER ONCE YOU RELEASE THE PEDAL THE FLUID DOES NOT ALL RETURN TO THE MASTER CYL. THE HOSE IS OLD AND THE RUBBER IS BUSTED INSIDE OF THE HOSE AND THE FLUID IS STAYING INSIDE OF HOSE AND HOLDING PRESSURE ON THE CALIBER. I HAVE HAD THIS HAPPEN TO ME AND NEEDLESS TO SAY IT COST ME AROUND $500.00 TO HAVE IT FIXED AFTER I REPLACED CALIBER, ROTOR AND BRAKES.

Sep 21, 2011 | 1994 Chevrolet Cavalier

1 Answer

Why is the front brake locking up on my 93 chevy silverado truck


Brake caliber is faulty replace caliber and flush brake system with new fluid.

Jul 12, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer

How to change 2001 crown victoria brake pads


Jack up car, remove the wheels, take out the two retaing bolts on the brake caliber, slide caliber up off brake disc, remove old brake pad, use a C-Clamp or big pair of Channel locks to compress the piston in to the brake caliber, Insert new brake pads onto caliber, slide brake caliber back over brake disc, reinstall the 2 retaining bolts. put tire back on. Repeat this till you have replaced all pads that you are going to change. ***Caution.. Before putting the car in gear, crank it up and pump the brake pedal till you have a firm brake pedal. If you fell to do this you will have no brakes due to the pistons on the calibers are compressed and are not seated on the discs.

Jan 08, 2011 | 2001 Ford Crown Victoria

3 Answers

Changing front disc brakes on 95 ford f250


Thats how I have done it on 2006 250. No C clamp.

Aug 03, 2010 | 1995 Ford F250

1 Answer

Front calibers keep locking up on my 96 dodge dakota 5.2


I would replace the rubber brake hoses at the calipers. They get damaged internally when the calipers are left hanging while replacing pads. I've seen too many garages and shops do it not knowing what is going on inside the hose.

May 06, 2009 | 1995 Dodge Dakota

2 Answers

Caliber bolts are stuck


If that is the problem...put your allen wrench or socket on the bolt. Then put a CRECENT wrench on that end of your ratchet....you need leverage....trust me, it will break loose.

Mar 13, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

2004 Chevrolet Silverado Extended Cab brake replacement


jack the truck up and take the passangers tire off. look behind the rotor you should see 2 bolts holding the caliber on to the rotor. loosen those and take them out. from there you should be able pull up on the caliber this will take the caliber and pads off together. take the pads out of the caliber and install the new ones .

BECAREFUL not to twist or bend the caliber to much or you will bend the brake line.....

once you have installed the new brake pads in the caliber. put the caliber back on the rotor. if they will not fit release the bleader valve to release the pressure. than you should be able to slid the caliber back onto the rotor. once you have done that close the bleader valve. reinstall the 2 bolts to hold the caliber in place. put your tie back one. Follow these steps for the other side.

now once that is done. you might want to blead the front breaks.
what you do is have someone help you. fill the brake resiviour with brake fliud. than start your truck.
Have someone in the cab to press the brake. What you want to do is turn the wheel so you can get to the bleader valve. once you can get to it open it up. have the person in the cab other truck press the brake until you see a steady flow of brake fluid coming out of the caliber. once you see that have the pseron press the brake once more and hold it to the floor.
close the bleader valve.

now do the same thing on the other side. But, make sure you check your resivour fluid first.
This is to make sure you don't have any air in the lines. after you are done with both side put it in gear and hit the brake make sure you stop......... If that works go about half the block down and hit the brake again to make sure you stop......
once you have done that and are comfortable with the way the truck stops than ou are good to go and now know how to change the brakes for future refrence..... be aware the back brakes are diffrent.........

let me know when you are ready for the back brakes.
do not blead the front ones if ou intend to do the back brakes afterwarwords......

if you are only doing the front brakes you must blead the the passanger side first......... if you do not have the bolts holding your caliber on than you will have a pin the you will take a hammer to and knock it out that will release them....

Aug 01, 2008 | Chevrolet 1500 Cars & Trucks

1 Answer

Disc brakes replacement


jack the truck up and take the passangers tire off. look behind the rotor you should see 2 bolts holding the caliber on to the rotor. loosen those and take them out. from there you should be able pull up on the caliber this will take the caliber and pads off together. take the pads out of the caliber and install the new ones .

BECAREFUL not to twist or bend the caliber to much or you will bend the brake line.....

once you have installed the new brake pads in the caliber. put the caliber back on the rotor. if they will not fit release the bleader valve to release the pressure. than you should be able to slid the caliber back onto the rotor. once you have done that close the bleader valve. reinstall the 2 bolts to hold the caliber in place. put your tie back one. Follow these steps for the other side.

now once that is done. you might want to blead the front breaks.
what you do is have someone help you. fill the brake resiviour with brake fliud. than start your truck.
Have someone in the cab to press the brake. What you want to do is turn the wheel so you can get to the bleader valve. once you can get to it open it up. have the person in the cab other truck press the brake until you see a steady flow of brake fluid coming out of the caliber. once you see that have the pseron press the brake once more and hold it to the floor.
close the bleader valve.

now do the same thing on the other side. But, make sure you check your resivour fluid first.
This is to make sure you don't have any air in the lines. after you are done with both side put it in gear and hit the brake make sure you stop......... If that works go about half the block down and hit the brake again to make sure you stop......
once you have done that and are comfortable with the way the truck stops than ou are good to go and now know how to change the brakes for future refrence..... be awar the back brakes are diffrent.........

Aug 01, 2008 | 1992 Chevrolet K1500

Not finding what you are looking for?
1992 Chevrolet C1500 Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...