Question about 1997 Plymouth Grand Voyager

1 Answer

How do i replace an alt on an 97 Grand Voyager?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 17,970 Answers

When you says ALT, I'm assuming that you are talking about ALTERNATOR...

REMOVAL & INSTALLATION
2.4L Engine

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Unplug the push-in field wire connector from behind the alternator.
  4. Remove the B+ nut and wire from behind the alternator.
  5. Remove the nut securing the top of the alternator to the adjuster bolt (a.k.a T-bolt).
  6. Remove the alternator pivot nut and bolt, located below the alternator.
  7. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install, but do not tighten, the alternator pivot nut and bolt.
  3. Install the nut securing the top of the alternator to the adjuster bolt.
  4. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  5. Plug in the push-in field wire connector onto the back of the alternator.
  6. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys, especially the alternator.
  7. Adjust the drive belt and tighten the adjuster/locking bolt to 40 ft. lbs. (54 Nm).
  8. Tighten the pivot bolt to 40 ft. lbs. (54 Nm).
  9. Reconnect the negative battery cable.
  10. Verify the charging rate of the alternator.

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  1. Remove the accessory drive belt from the alternator.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  1. While holding the alternator, unplug the push-in field wire connector from behind the alternator.
  2. While holding the alternator, remove the B+ nut and wire from behind the alternator.
  3. Remove the alternator from the vehicle.
To install:
  1. Hold the alternator in position near the mounting bracket, then connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  2. Plug in the push-in field wire connector onto the back of the alternator.
  3. Place the alternator into position on the mounting bracket, then install the bolt securing the bottom of the alternator to the lower pivot bracket.
  4. Install the bolt securing the top of the alternator to the mounting bracket. Tighten the upper and lower alternator bolts to 40 ft. lbs. (54 Nm).
  5. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  6. Install the windshield wiper/motor module assembly.
  7. Reconnect the negative battery cable.
  8. Verify the charging rate of the alternator.

3.3L and 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  1. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the alternator mounting bracket from the vehicle.
  4. Rotate the alternator toward the dash panel.
  5. Unplug the push-in field wire connector from behind the alternator.
  6. Remove the B+ nut and wire from behind the alternator.
  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

Hope helps woth this, remember rated this help. Good luck.

Posted on Jul 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem getting 97 van to start


All timing marks aligned and distributor rotor pointing at # 1 cylinder at TDC as it should? All that has been confirmed properly aligned? What engine?

Mar 29, 2014 | 1997 Plymouth Grand Voyager

1 Answer

I need help timing my plymouth 97 grand voyager


Timing is not adjustable and why would it change??

Jul 17, 2012 | 1997 Plymouth Grand Voyager

1 Answer

Power steering not working sometimes on 97 plymouth grand voyager


Is the steering rack 14 years old?

Have you flushed the fluid every 30,000
miles ,since new

Does the system leak and your low on fluid

We need all that when you ask a question !!

Mar 18, 2011 | 1997 Plymouth Grand Voyager

1 Answer

97 Plymouth Grand Voyager 3.3 engine. The transmision just started slipping. The fluid level is fine and there are no leaks. There are no check engine lights on. Was running perfectly. What is the problem?


I have replaced alot of transmissions in thease vans, i would try changing the filter and fluid, if that doesn't help you may be looking at replacing the tranny.

Oct 23, 2010 | 1997 Plymouth Grand Voyager

1 Answer

Misfire in 97 voyager,P0300 and P0304,HELP! Need 2 get inspection


I'd have fuel pressure checked, and at the very least, replace fuel filter. Not unusual to get multiple misfire codes due to low fuel pressure, thus starving cylinder(s), and causing the misfire code(s).

Apr 23, 2010 | 1997 Plymouth Grand Voyager

1 Answer

How to change oil pump on plymouth grand voyager


go to http://www.autozone.com/autozone/homePage.jsp and sign up, put in your vehicles info and click on repair guides, they have oil pan remove and replace but no guide for the oil pump but its located in the oil pan and usually held on with 2 bolts and a gasket inside the pan, Tough job probably need someone with mechanical experience to help with this.

Apr 18, 2010 | 1997 Plymouth Grand Voyager

2 Answers

1997 plymouth grand voyager v6 3.0L broken timing belt


I had the same thing happen, No, I was told this is not one of the engines that allows the piston to contact the valves. I replaced the timing belt 2 years ago and had no valve problems.

Sep 22, 2009 | 1997 Plymouth Grand Voyager

1 Answer

I have a 97 plymouth grand voyager sometimes it will start other times wont i replaced one computer but it still does it starter is new and the guages quit working help


You need to pull out the Printed Circuit board behind the dash board gauges and re-solder ALL the parts on the board. Only attempt this if you are experienced at soldering electronic PC boards as you could permanently damage the board.

Mar 31, 2009 | 1998 Plymouth Grand Voyager

1 Answer

3.3 L 97 Grand Voyager engine won't idle revs stay at 2200 - 3000 rpm


Possibly the oxygen sensor. Had same problem with my Accord, had oxy sens replaced and that not only fixed the problem but I got better gas mileage after that.

Aug 27, 2008 | 1997 Plymouth Grand Voyager

Not finding what you are looking for?
1997 Plymouth Grand Voyager Logo

906 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8501 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...