Question about 2000 Mazda MPV

1 Answer

Belt replacement diagram 2000 mazda mpv

Belt replacement diagram

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 6,826 Answers

REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.

  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1⁄2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range. Fig. 1: Often the underhood label will display the serpentine drive belt routing belt replacement diagram 2000 mazda mpv - 88231p43.gif
    Fig. 2: Relieve the belt tension by pivoting the automatic tensioner away from the belt, then remove the belt 88231p44.gif
    Fig. 3: Verifying serpentine belt alignment in the pulley 79244g60.gif
    Fig. 4: Fig. 1 Accessory V-belt routing (alternator) — Mazda MPV 3.0L engine 79244g67.gif
    Fig. 5: Fig. 2 Accessory V-belt routing (power steering) — belt replacement diagram 2000 mazda mpv - 79244g66.gif0L engine 79244g66.gif
    Fig. 6: Fig. 3 Accessorbelt replacement diagram 2000 mazda mpv - 79244g65.gifting (A/C compressor) — Mazda MPV 3.0L engine
belt replacement diagram 2000 mazda mpv - next.gif"http://arrc.epnet.com/autoapp/9308MPV/9308CH03_ADJUSTMEN1.htm">prev.gif next.gif

Posted on Jul 08, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 155 Answers

SOURCE: need a free diagram on how to replace the

ok a drew it
a3c549c.jpg

Posted on May 14, 2010

  • 66 Answers

SOURCE: how do I replace alternator in mazda mpv 2000?

It is not a very difficult task, but one that would be better left to a professional for a couple of reasons. First, the system should be tested to be sure this is going to fix your problem. Many times a bad battery is the demon. Second, you will get a warranty with that repair if you have it done at a reputable garage/dealership. Just a couple of things to think about.

Posted on Jan 05, 2009

  • 1 Answer

SOURCE: 2000 Mazda MPV

I NEED THE DIAGRAM FOR SERPENTINE BETL FOR MAZDA 2000 MPV

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

3 Answers

When do I replace the timing belt


hi.
a 2000 mpv should be the newer model (older model stopped 1998)
all newer models were fitted with a timing CHAIN which does not need routine replacement.

Mar 02, 2011 | 2000 Mazda MPV

1 Answer

How to change a timeing belt


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1995 Mazda MPV. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1995/make/mazda/model/mpv/1995_mazda_mpv_timing_belt_diagram_marks.htm

Mar 12, 2010 | 1995 Mazda MPV

2 Answers

Where do i find the water pump and how much to replace.


INFO:
Water pump runs off of the timing belt.

ANSWER TO QUESTION:
Water pump can be replaced for about $300.00

RECOMENDATION:
Use only factory original belt.

Hope this tip helps.\

R/
David

Jan 31, 2010 | 2000 Mazda MPV

2 Answers

Replacing neutral safety switch on 2000 mazda mpv


ALLData.com probably has the best info for your MPV. I use it for my 2000 MPV and it hasn't failed me yet. Mazda wants $250 for a shop manual and Haynes hasn't written one as of yet. My MPV right now won't come out of 2nd gear because of (I'm hoping) a bad PRNDL Range Select Switch.

Mar 19, 2009 | 2000 Mazda MPV

1 Answer

How do i replace the alternator on mazda mpv 2000?


Remove negative (-) battery terminal from battery. Remove drive belt from alternator pulley. Remove wiring harness (electrical connections) from alternator. Remove attaching bolts for alternator. Pry out alternator. Reverse steps to reinstall. 

Dec 23, 2008 | 2000 Mazda MPV

2 Answers

2000 Mazda MPV


I NEED THE DIAGRAM FOR SERPENTINE BETL FOR MAZDA 2000 MPV

May 17, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
2000 Mazda MPV Logo

2,139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...