Question about 1995 Honda Accord

1 Answer

Turns over but wont start

Replaced starter, now it turnsover but wont start have got it to start a couple of times it is o.k. for the day then sits all night and wont start again

Posted by on

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Check the ignition control module

Posted on Jul 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 corolla wont crank and start


Sounds like your ECM / ECU may need to be re-flashed at the dealer, have you tried pulling the codes? The check engine light does NOT need to be on for it to have codes stored. The starting issue could be caused by the TPS / MAF / MAP sensors, the flashing of the odometer could be something with your PSOM chip or your VSS sensor. Pull the codes see what you get.

Sep 13, 2015 | 2010 Toyota Corolla 1.8

1 Answer

2001 Rodeo 2.8 Turbo Diesel running perfectly one day won't run the next. Seems to be after it sits for a couple of days. Any suggestions?


Hi Peter, If the vehicle turns on the starter all the time, and sometimes starts and other times fails, check the fuel filter for leakage. Sometimes air gets into the fuel system. When it gives problems, open the bonnet (hood) and have someone pump the pump on top of the filter housing. If it feels soft when beginning to pump, I would suspect either a leakage on the fuel line or the filter housing. If you need to replace the housing and filter, remember to fill the replacement filter with clean diesel fuel first. the glow plugs can also cause problems if one or more have burned out. Regards John

Oct 31, 2012 | Cars & Trucks

2 Answers

My car, a 1999 300 M, when it sits for a couple of days wont start on the first try..it will click ...sometimes but you have to keep turning the key on over and over.. some thimes it takes longer to start...


Yes, you have dead spots an the starter commutator. The way to tell is this: the next time it happens, get a hammer and hit the starter dead on the side. If it then starts, replace the starter.

Mar 16, 2011 | Chrysler 300M Cars & Trucks

1 Answer

Everything in elec. system has been replaced including coil distributer ecm.,but car will start one day but not the next,leave it sit a couple days and it runs again.


if it turns over but doesnt run, check the hall pickup in the distributor. if it wont turn over at all, its the brown goundwire connected in the engine compartment on the drivers side halway between the starter motor and the master cylinder.

Sep 13, 2010 | 1984 Dodge Rampage

1 Answer

Wont turn over


The starter is most likely the problem,tap on the starter lightly with a hammer while trying to start the engine,dont get run over doing this it will take two people,if the engine starts,the starter needs replacing.

Apr 25, 2010 | 1998 Jeep Wrangler

1 Answer

2002 Jetta Wont start if its turned off for less than 30 minutes


starter is going bad will work when cool but not after engine has warmed up heat from engine is impairing operation of starter replace the starter and it should cure this

Aug 18, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

2004 pontiac grand am wont start


yes the gauges should go up and down they are selftesting your starting problem could be starter related they were having problems with those, also try turning ignition to the on position for 3 seconds before trying to start,also gm has a tsb for hard start issues

Nov 12, 2008 | 2004 Pontiac Grand Am

1 Answer

Starter


you can replace the cylinoid,but I prefer to change the whole thing specially that it seems like starter drag when you buy the new starter the cylinoid will be built on the new starter,if you change the cylinoid itself,and you still need a starter youll have to buy the starter and cylinoid as one unit,and they wont take the cylinoid back that you broke,but either way I would pull the starter and bring it down to an autozone and have it checked for free,if this helps please give me a fix ya

Jul 17, 2008 | 1995 Nissan Quest

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...