Question about 2001 Chrysler Town & Country

1 Answer

My town % country van stopped shifting. - 2001 Chrysler Town & Country

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 274 Answers

Can you explain more?

Posted on Jul 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the alarm system stop my 1999 town and country van from starting


Probably needs the fuel safety shutoff switch resset. I am not sure where it is on a Town and Country van.

Nov 29, 2014 | 1999 Chrysler Town & Country

1 Answer

What stops my transmission from going into gear?


your tranny is shot,like most chrysler vans,the tranny sucks,1200 to fix,junk it

Jun 17, 2014 | 1999 Chrysler Town & Country

1 Answer

2000 chy town/country intakek


I doubt it also. Shift Solenoids possibility

Clogged CAT

Apr 10, 2013 | 2000 Chrysler Town & Country

1 Answer

After battery disconnect what needs reprogram - 2001 town and country


Besides the normal stuff, like the radio stations preset and the clock, the only thing that has to be reprogramed on these vans is the shifting, somtimes it looses its shift points, you will need to reconnect the battery and then drive the van and you will see if it doesnt shift gears like it used to, it may take longer to shift, to correct this problem dissconnect battery for 10min, then connect it back and start the van and place the shifter all the way down to low, slowly roll out to road and take off you will shift the gears your self, note that the way you shift is the way its programed, so you will take off and at about 15mph you will shift to 2 and then i think at 30mph 3 and so on till you get to drive, good day.

Sep 06, 2011 | 2001 Chrysler Town & Country

1 Answer

My 1996 town and country wont shift..It was shifting but then would stop but if we pulled over and re started it it would shift fine again. But now it isnt shifting at all..We have a computer hooked for it...


we can here,
your van is going into "limp mode"
when the computer does not get a correct signal from transmission it will not shift because it doesn't know your speed or engine RPM,
Three sensors on the transmission will trip it into limp mode,
1= output sensor,
2=input sensor,
3=speed sensor,
if you have it checked and get a "P0000" type code
it will tell you which one

Dec 18, 2009 | 1996 Chrysler Town & Country

1 Answer

Van is not shifting out of 2nd gear?


I am going to assume you have the overdrive trans. This trans defualts to second gear if the trans computer detects there is a problem.

This problem can be anything from internal falure to sensors that are bad. You have to scan it for trans codes. It could be a simple input or output speed sensor. that is the easiest. however you have to start with the scan.

Most Advance and Autozone parts stores will scan for free.

Hope this helps and hope it is not internal.

Oct 06, 2009 | 1996 Chrysler Town & Country

1 Answer

1996 CHRYSLER TOWN & COUNTRY TRANS AXLE PROBLEM.


i had same toublre on 96 plymouth output speed senor my wont shift out of second

Dec 06, 2008 | 1996 Chrysler Town & Country

1 Answer

Fix a 1998 town and country van


hi i had the problem it was the circut board solder,in the dash cluster

Oct 03, 2008 | 1998 Chrysler Town & Country

1 Answer

Shifts into gear roughly


the pin in the differential inside the trans probably came out. you need a new transmission since this usually causes major case damage.

May 27, 2008 | 1998 Chrysler Town & Country

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...