Question about 1995 Chevrolet K1500

1 Answer

Hi experts ! I replaced the gear box on a 1995 Chevy G10 van ( my first ) and now I have more left turn than right turn . I think I have to remove the P arm ( is there a trick to that ? ) and adjust the steering but I don't know how . Thanks for your advice !!!!!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 645 Answers

Yes you will have to remove the pitman arm and turn the gear box so that it turns more to the right. it has slots so align it on the next slot to the right. they make a tool that they call a pitman arm puller that raps around the pitman arm and puts pressure on gear box shaft wile turning it clock wise. you'll figure it out once you see the tool. the big nut usually takes 1 1/4 inch socket. hope this helps

Posted on Jul 08, 2010

Testimonial: "thanks, so do I need to keep the wheels straight and just turn the steering wheel to the left ? "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition switch on a 1995 Chevy g10 van


The switch (electrical part) is located at the bottom of the steering column on the top I think. Use small open end wrench to remove mounting screws and disconnect wires. Replace and reconnect and follow instructions with new unit to align. If I'm wrong and yours is inside the column, best to buy a shop manual as it's going to be a bi**h.

Jan 04, 2015 | Cars & Trucks

2 Answers

2004 chevy 1500 ext cab hard to turn right at low speeds


2004 chevy tahoe 4x4 had the same problem wont turn right at idle - like no power steering , has hydoboost brake steering system , did test and found steering box bad , removed box and remove the top cover on box 4 bolts at hydralic cover and removed and found spool valve has 4 seals 1 outer was blown i replaced box with reman from advance auto about $200.00 and flushed system , drove great problem solved .

Aug 26, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

In order to remove the P/S Gear Pitman Shaft Lower Seal where the Pitman arm is attached on a 1995 chevy G10 van , can the seal be removed from the outside by just removing the Pitman arm or does the gear...


Once you have the arm removed (use a puller made for that) You need to remove the c clip retainer. Many times you can loosely install the arm, put it back on the ground and with a catch pan under it, just quickly turn the wheel and pressure will drive the seals out. If that does not work, you can use long self tapping screws and put one into each side of the seal and pull it free. Most i've seen always have two seals separated by a steel flat washer. To re-install, you need to carefully drive the seal back in using a piece of pipe or anything that fits and does not damage it. I have special tools I made long ago to do that but the trick is to be careful not to get the seal too far in on any one side and to not damage it in any way. Likely someone makes an install tool. Make note of the order of the seals as you remove them and make a reference mark on the arm and shaft so you can get back together the same way it was.

Jun 25, 2010 | 1995 Chevrolet K1500

1 Answer

How do you know if the gear box is gone on a peugeot expert van? The gear shaft is gone all loose and i can't get it to go into gear. I haven't had any problems recently with the gears and there was no...


Could but just the gearbox selector rod has come loose a local garage may be able to fix problem within half an hour without removing or replacing gearbox and should only cost very little.
If there was not major bang then i doubt any gearbox trouble it will just be a simple linkage issue.

Jun 22, 2010 | Cars & Trucks

2 Answers

HOW CAN I FIX A GEARBOX OF AN AUTOMATIC NISSAN B14


Auto boxes are best left to professionals but there are some things you can do 1) check that the selector rod from beneath the gear shift to the gear selector on the side of the gear box is correctly adjusted, 2) make sure that the transmission oil is at the right level, new oil can be added via the dip stick tube. If you are adventurous and are able to remove the gearbox pan you might be to see evidence of the gear box damage, metal shavings etc. If you can remove the gearbox you may be able to replace a sheared splined input shaft (indicated by a an engine that is running but that will simply not engage gear). Anything repairs beyond this should be left to an expert or simply replace the gearbox

May 07, 2010 | 1995 Nissan 200SX

1 Answer

Reverse wont engage in my 1998 cevy 10 van


Considering the age and possible milage put upon your transmission at this point in time it is very possible that the valve body is at fault. There are several small ball bearings that position themselves during gear changes. These, over a period of time can accumulate a pasty type of buildup that will not remove it self which causes them to sit incorrectly in there sinks.The sinks therefore become ovalized causing a open seal situation. My suggestion at this time would be a rebuild, if, you think it is worth it. Shop around!! Very important.

Sep 21, 2009 | 1989 Chevrolet G10

1 Answer

1984 chevy g10 van - window seals are old and


yes you must remove all, or it won't seal properly

Jul 27, 2009 | 1985 Chevrolet Sportvan G10

Not finding what you are looking for?
1995 Chevrolet K1500 Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...