Question about 1990 Plymouth Acclaim

1 Answer

Change the ignition modular on the steering column, and now the air bag lite does not come on, and there is no power to the starter. The power windows work, and the heater fan, but will not crank.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,272 Answers

The ignition module is not connected properly.The ignition module is not letting the power to ignition coil so that they can spark/crank.Check the voltages at all the parts this will indicate the faulty part in few minutes.It will show exact 12 volt.Start checking from car battery,then starter,then the ignition coils,then the module itself . Its the short in the dash control wires if in case all the voltages checked out ok. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Posted on Jul 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the steering wheel for replacement


SIR DISABLE:
DRIVER SIDE
Many service procedures require the air bag system to be disabled to prevent accidental deployment. The air bag system can maintain sufficient voltage to cause deployment for up to 2 minutes after the ignition switch is turned off, the battery ground cable is disconnected or the DERM fuse is removed. If the inflator module is disconnected from the deployment loop by the following procedure, service can begin immediately without waiting for the 2 minute time period to elapse.
  1. Turn steering wheel so that vehicle wheels are pointed straight ahead.
  2. Turn ignition switch to Lock position and remove key.
  3. Remove air bag fuse from fuse block.
  4. Remove steering column filler panel.
  5. Remove Connector Position Assurance (CPA) and disconnect yellow two-way connector at base of steering column, Fig. 1.
PASSENGER SIDE
  1. Remove air bag fuse from fuse block.
SIR ENABLE:
Driver Side
  1. Turn ignition switch to LOCK and remove key.
  2. Connect yellow two-way connector and install connector position assurance (CPA).
  3. Install steering column filler panel.
  4. Insert air bag fuse into fuse block.
  5. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.
Passenger Side
  1. Turn ignition switch to LOCK and remove key.
  2. Insert air bag fuse into fuse block.
  3. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.

remove-steering-wheel-replacement-rfvykuizssn2qn2mhtsbw2yl-3-0.png

Apr 10, 2015 | 1996 Chevrolet K1500

1 Answer

Does the air bag need to be disconnected when replacing a stearing wheel cruis control switch on a 2001 buick lesabre custom?


Anytime you are working on the steering wheel or steering column, the battery should be disconnected and the power drained from the car.
If a wire is shorted in the air bag circuit the bag could deploy.
Even if the ignition is turned off.
The standard procedure is to leave the door open and disconnect the battery, then wait 5 or 10 min to drain power from the car.

Feb 26, 2013 | Cars & Trucks

1 Answer

On my altima 96 when I'm parking or turning extremely slow the steering wheel somewhat locks


Hi, can you tell if it's the lock in the steering column or something with the power steering instead? If it feels like the power steering, check the belt for looseness and tighten as needed. If it feels like it's in the column, your locking assembly may be coming loose inside. Below is a procedure for removing the steering wheel lock for inspection. Please let me know if you have questions, and thanks for using FixYa.


REMOVAL & INSTALLATION The steering lock/ignition switch/warning buzzer switch assembly is attached to the steering column by special bolts whose heads shear off upon installation. The bolts must be drilled out to remove the assembly or be removed with an appropriate tool. The bolts may also be removed with a hammer and chisel by notching the bolts and tapping them counterclockwise with the hammer and chisel.
The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch is on the side.


CAUTION The models covered by this guide may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Chassis Electrical .

  1. Disable the air bag system by disconnecting the negative battery cable and waiting at least 10 minutes, prior to starting this procedure.
  2. Remove the steering column covers.
  3. Remove the steering wheel.
  4. Remove the spiral cable assembly.
  5. Remove the combination switch from the steering column.
  6. Remove the steering column support nuts and lower the steering column.
  7. Disconnect the ignition switch wiring.
  8. Remove the bolts that secure the steering lock and remove the steering lock assembly.

To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness.
  3. Raise the steering column and secure with mounting nuts. Tighten the mounting nuts to 11-14 ft. lbs. (15-19 Nm).
  4. Install the spiral cable assembly.
  5. Install the combination switch.
  6. Install the steering column covers.
  7. Install the steering wheel.
  8. Connect the negative battery cable.

Apr 04, 2011 | 1996 Nissan Altima

1 Answer

Hi, i have 1991 mazda protege. I accidentally broke my key in the ignition lock and now i was wondering how do you take off the ignition lock cylinder? p.s key was pretty worn down already


Ignition Switch/Lock Cylinder REMOVAL AND INSTALLATION CAUTION
Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6. The ignition lock is an integral component of the steering lock mechanism. If the ignition lock must be replaced, perform the following procedure. Fig. 1: Exploded view of the ignition switch/lock cylinder assembly 89548g14.gif
Fig. 2: Remove the break-off head retaining bolts by chiseling a slot in the bolt, then removing them with a screwdriver 89548g15.gif
Millenia
  1. Disconnect the negative battery cable.
  2. Properly disarm the air bag system.
  3. Remove the rear console box, brake boot and center panel (disconnect the harness connectors).
  4. Remove the rear console.
  5. Remove the undercover, glove compartment and compartment cover.
  6. Remove the upper and lower steering column covers.
  7. Tilt the steering shaft down. Remove the cap and panel light control switch. Remove the meter hood mounting screws. Pull the meter hood forward to disengage the clips.
  8. Remove the instrument cluster,
  9. Remove the drivers side air bag and the steering wheel.
  10. Remove the combination switch.
  11. Remove the passenger side air bag mounting bolts, electrical connector and remove the air bag module.
  12. Remove the hood panel release lever. Pull the side panel forward to disengage the clips, remove the side panel.
  13. Remove the side covers.
  14. Remove the dashboard mounting bolts, pull the dashboard up and forward and remove.
  15. Remove the steering shaft.
  16. Remove the screw and the ignition switch and disconnect the ignition switch connector.
  17. Using a chisel and a hammer make a groove in the heads of the steering lock mounting bolts. Remove the bolts and the steering lock assembly. To install:
  18. Install the steering lock mechanism to the steering column jacket. Make sure that the lock operates correctly. Install new mounting bolts and tighten the bolts till the heads break off.
  19. Reconnect the ignition switch connector to the ignition switch and install the ignition switch to the steering lock mechanism with the screw.
  20. Replace the dashboard close to its mounts and connect all harness connectors. Install all mounting bolts. Torque to 14-18 ft. lbs. (19-25 Nm).
  21. Install the side covers.
  22. Instal the side panels.
  23. Install the steering shaft and torque the mounting bolts to 12-16 ft. lbs. (16-22 Nm).
  24. Connect the passenger side air bag module electrical connector and replace the module to the dash and install the mounting bolts.
  25. Install the combination switch on the steering column.
  26. Install the steering wheel and drivers side air bag module.
  27. Install the instrument cluster.
  28. Install the meter hood.
  29. Install the upper and lower steering column covers.
  30. Install the glove compartment cover, compartment and the undercover.
  31. Install the rear console, bracket, center panel, brake lever boot and the rear console box.
  32. Reconnect the negative battery cable,
  33. Place the steering column securely on a workbench. Use a chisel and hammer to make slots in the head of the lock screws. Remove the screws.
Except Millenia
  1. Disconnect the negative battery cable.
  2. If equipped, disarm and remove the air bag.
  3. Remove the steering wheel and the combination switch.
  4. Remove the steering column by performing the following:
    1. Remove the driver's side under dash covers.
    2. If equipped, disconnect the key interlock cable from the steering column.
    3. Detach any remaining electrical wire harness connectors from the column.
    4. Remove the upper column-to-dash mounting bolts. Support the steering column.
    5. Remove the intermediate shaft-to-steering column shaft coupling bolt and remove the steering column-to-firewall bracket bolts/nuts.
    6. Remove the steering column from the vehicle.
  5. Place the steering column securely on a workbench. Use a chisel and hammer to make slots in the head of the lock screws. Remove the screws.
  6. Remove the ignition lock assembly. To install:
  7. Position the ignition lock and bracket on the steering column.
  8. Install the new screws until the head twists off. Make sure the lock operates properly while tightening the new locking screws.
  9. The remainder of the installation is the reverse of the removal procedure.
prev.gif next.gif

Feb 12, 2011 | 1993 Mazda Protege

1 Answer

Ignition switch removal and repair for 1995 crown victoria


  1. Disable air bag system.
  2. Remove steering column shroud by removing self-tapping screws. Remove tilt lever if equipped.
  3. Remove instrument panel lower steering column cover.
  4. Disconnect ignition switch electrical connector.
  5. Rotate ignition key lock cylinder to RUN position, then remove two screws retaining ignition switch.
  6. Disconnect ignition switch from actuator.
  7. Reverse procedure to install, noting the following:
    1. If necessary, move switch slightly back and forth to align mounting holes with column mounting holes.
    2. Activate air bag system.
    3. Ensure proper operation of ignition switch in all positions.

Nov 23, 2010 | Ford Crown Victoria Cars & Trucks

5 Answers

I have a 1996 Miata where the alarm system goes off no matter what I do to the secuirty switch on the steering column. It can be in the off position or on and open a door and the alarm contiues to go off....


Check wires connections in ALARM WIRING DIAGRAM

Also, its possible that this info helpfull:
- Power Lock - TO DRIVERS DOOR ONLY, See DIAGRAM
- Power Unlock - TO DRIVERS DOOR ONLY, See DIAGRAM

Keepo us updated and send comments.

Oct 17, 2010 | 1996 Mazda MX-5 Miata

1 Answer

Can I use regular atf fluid for power steerig fluid in my 1991 porsche c2 cabriolet without any problem? Where is the modular for the seat belt and air bag on same car?


hi you will need dexron 2 (II) for the power steering, modular? if you mean the seat belt pre-tensioner this is found under the seat, and air bag..the control module for the air bag is below the steering wheel under the dashboard....hope i got these right, if not can you elaborate on the modular???? as this means round in the uk, eg modular type frame work=tubed frame..hope this helps if not just get back to me

Sep 19, 2010 | 1991 Porsche 911

1 Answer

Remove ignition switch for a 2004 kia optima


Ignition Switch Removal & Installation To Remove:
  1. Disconnect battery negative cable.
  2. Disarm air bag system.
  3. Remove driver air bag module.
  4. Loosen screw and lift horn pad to remove.
  5. Remove lock nut and washer. CAUTION
    Do not hammer on steering wheel. Damage can occur to the energy absorbing portion of the steering column.
  6. Pull dynamic damper forward and lift up to remove.
  7. Remove steering wheel.
  8. Remove steering column shrouds.
  9. Remove lower cover.
  10. Remove multifunction switch.
  11. Remove entire lower portion of dash.
  12. Remove mounting fasteners and lower steering column.
  13. Remove bolts and separate ignition switch from steering column.
To Install:
  1. Install ignition switch to steering column and install bolts.
  2. Raise steering column and install mounting fasteners.
  3. Install lower portion of dash.
  4. Install multifunction switch.
  5. Install lower cover.
  6. Install steering column shrouds.
  7. Install steering wheel.
  8. Install dynamic damper.
  9. Install washer and lock nut.
  10. Lift horn pad and install screw.
  11. Install driver air bag module.
  12. Connect battery negative cable.
prev.gif next.gif

Jul 17, 2010 | 2004 Kia Optima

1 Answer

Now to install igintion switch


Removal & Installation The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch on the side.
  1. Disconnect the negative battery cable and insulate the terminal end.

CAUTION The air bag system must be disarmed before removing the steering wheel. Failure to do so may cause accidental deployment, property damage or personal injury.

  1. Remove the steering wheel and the steering column upper and lower covers.
  2. Remove the spiral cable assembly.


23482ab.gif
View of the steering lock and ignition switch assembly

  1. Remove the combination switch from the steering column.
  2. Remove steering column support nuts and lower the steering column.
  3. Disconnect the ignition switch wiring and interlock cable (if equipped).
  4. Remove the bolts that secure the steering lock and remove steering lock assembly.
To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness and the interlock cable.
  3. Raise the steering column and secure with mounting nuts.
  4. Install the spiral cable assembly.
  5. Install the combination switch, steering column covers, and the steering wheel.
  6. Connect the negative battery cable and enable the air bag system.

May 23, 2010 | 1997 Nissan Maxima

1 Answer

Where is the ignition switch on a 2004 pontiac sunfire


The ignition switch is in the steering column.You need to be very careful when working with the steering wheel because of the air bag.If your are not familiar with taking apart a steering column with an air bag system then you should have a certified technician do it.

Nov 17, 2009 | 2005 Pontiac Sunfire

Not finding what you are looking for?
1990 Plymouth Acclaim Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...