Question about 2005 Chevrolet TrailBlazer

Open Question

Where is the camshaft position sensor on a 2005 chevy trailblazer

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
savdragon
  • 37 Answers

SOURCE: locate camshaft sensor 2002 chevy trailblazer

Assuming you have a 4.2L engine here is the location.
b3031ef.gif

Hope this helps out,
if so please rate my answers.
Brett

Posted on Mar 19, 2009

Ad
  • 30 Answers

SOURCE: 2002 Chevy Trailblazer Engine Codes

This is actually an easy swap out. Remove the electrical connection, remove the retaining bolt and pull out old one. I believe the sensor is located in the front passenger side of the engine on this particular model.

Posted on Aug 16, 2008

  • 462 Answers

SOURCE: p0014 engine code

THE CAM SHAFT ACTUATOR IS LOCATED IN THE CYLINDER HEAD ON THE FRONT RIGHT HAND SIDE JUST ABOVE THE POWER STEERING PUMP. AFTER YOU REMOVE THE ACTUATOR CHECK TO SEE IF ANY OF THE SCREENS ARE DAMAGED OR MISSING. IF SO REPLACE THE ACTUATOR. ALSO CHECK THE CRANKSHAFT END PLAY. IT SHOULD BE BETWEEN 0.0044" - 0.0153". if excessive crankshaft end play is causing this concern, it will be obviously out of specification by as much as.050" or more when a pry bar is used to move the crankshaft back and forth. IF THIS IS THE CASE AN ENGINE REPLACEMENT IS RECOMMENDED DUE TO THE AMOUNT OF DEBRIS IN THE ENGINE. IF NO EXCESSIVE CRANKSHAFT MOVEMENT NOTICED REPLACE THE CAM ACTUATOR. IT WILL ALSO BE NECESSARY TO DO AN OIL CHANGE.

Posted on May 23, 2009

  • 14036 Answers

SOURCE: 98 silverado 5.7L camshaft position sensor

ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Posted on Oct 23, 2009

d_hubbs
  • 270 Answers

SOURCE: How do I change a camshaft position sensor on a

Hi : Your CPS (Camshaft position sensor) is located on the Engines Front Cover (Timing Chain Cover) its right below your Cylinder Head ,Get a Good Bright Light to Locate it ,You'll see a Wiring Connector plugged into the Sensor, emove the electrical Plug.
Then you have 1- Screw Holding it in Place -Remove the Retaining Screw and Remove the Sensor.

To replace it with your new Camshaft Sensor Put the Camshaft Sensor in where you took out your Old one,Replace the Retaining Screw Tighten up Good And Snug,Put the Wiring connector back on the Sensor and Your Done. This will get your job done,Let me know Please how My Solution/instructions have Helped you. Thanks From d_hubbs

Posted on Jun 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine codes 1415 and 1345 on a 2002 4.2 chevy trailblazer ls


1415 secondary air injection system bank 1
1345 crankshaft position-camshaft position correlation
You have something wrong with either your camshaft or crankshaft sensors. That's why car won't run

Jul 06, 2017 | 2002 Chevrolet TrailBlazer

1 Answer

P0014 Diagnostic code, already replaced camshaft actuator & oil twice


code p0014 - Chevy TrailBlazer, TrailBlazer SS and GMC Envoy Forum

forums.trailvoy.com > ... > OEM Issues

Sep 8, 2007 - 11 posts - ‎8 authors
On my Trailblazer I have a code P0014 . this says Camshaft Position Actuator B ... If the desired and actual cam phase angle error exceeds its ... This diagnostic procedure supports the following DTC: ... replace the camshaft actuator solenoid, change the engine oil and filter, ... 2004 Chevy TrailBlazer LT P0014 - Camshaft Position Actuator Solenoid "Relearn"
11 posts
Dec 11, 2009
cam crank sensor mismatch
11 posts
Jul 4, 2009
More results from forums.trailvoy.com

Tech Code "dtc P0014" 2003 Trailblazer - Chevy S-10/Blazer ...

www.gm-trucks.com/.../72278-tech-code-dtc-p0014-2003-trailblazer/

Dec 31, 2007 - 14 posts - ‎6 authors
Tech Code "dtc P0014" 2003 Trailblazer - posted in Chevy ... it had been serviced before for the same thing in 2003 or 2004! ... replace the camshaft actuator solenoid, change the engine oil and .... The extended war. co. prob. would not be to happy since they already fixed the sensor once or twice already.

Replace a Camshaft Position Actuator Solenoid Valve on a ...

? 8:05
https://www.youtube.com/watch?v=4Dkdd287AKg

Jan 11, 2016 | 2004 GMC Canyon

1 Answer

Camshaft position


It is camshaft position sensor it say to the computer when to send the spark at the spark plug and where are the piston and the valve


On old car the distributor do that job with cap and rotor, spark advance and vacuum advance

Apr 17, 2014 | 2005 Chevrolet Trailblazer Ext

1 Answer

Location on 2005 trailblazer of Camshaft Position Sensor


4.2l engine cmp sensor located front right corner of the engine cylinder head. 5.3l engine cmp sensor location front of the engine block just above the crankshaft.

Nov 23, 2011 | 2005 Chevrolet Trailblazer Ext

2 Answers

Would like to know where the Cam Shaft Sensor is located in 2002 Trailblazer.


it is the sensor that is being pointed at in the cylinder head


9a01378.jpg

Sep 12, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

P0014 code and the cruise will not work


DTC P0014 Exhaust Camshaft Position (CMP) System Performance.

The cam phasing system is a hydraulically actuated phase shifting mechanism. The powertrain control module (PCM) supplies the ignition positive driver and ground circuits. A pulse width modulated (PWM) driver controls the amount that the camshaft actuator solenoid assembly advances or retards the exhaust camshaft. The exhaust camshaft is commanded to a maximum ****** position of 25 degrees. When the exhaust camshaft is retarded at the maximum rate, the duty cycle of the signal is at 100 percent. The maximum advance rate has a 0 percent duty cycle. Other than when the camshaft is at full advance, a 50 percent duty cycle is used to maintain a steady ****** angle.

Remove Cam Phaser Solenoid and inspect it to ensure that all 3 screens are intact. Chances are you will need to replace this Solenoid and change the oil immediately.

Feb 24, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

Where is the camshaft position sensor located on 2005 chevrolet trailblazer


depending which motor you have one is located on the damper down on the right lower side of the drivers side the other located side of block passenger side

Jan 15, 2010 | 2005 Chevrolet TrailBlazer

Not finding what you are looking for?
2005 Chevrolet TrailBlazer Logo

Related Topics:

538 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...