Question about 1992 Honda Accord

1 Answer

How to replace brake booster on a 92 honda accord

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

There are 4 bolts that hold it on behind the dash as well as a pin that holds the brake lever to the pin on the booster. You have to pull the master cylinder off, the brake booster vacume hose, then get the 4 bolts and pin out from under the dash. The 4 bolts are a rotay pain in the ***.

Posted on Jul 07, 2010

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 1984 Honda Accord Brake Problem

Hi............

On your problem with the HONDA..
You are right the Problem is the BRAKE BOOSTER.
But before replace Inspect the Vaccum hose coming from the Intake manifold, Check for proper vaccum,
If everything is ok.
JUst replace the BOOSTER And the car will be ok.
Because the Brake Booster is LEAKING vaccum air.
And the ENgine will come at high IDLE..
Is why the engine will Run and DIE.

DON'T drive the car until you fix. Because is Danger for not Brake response.

OK.. I hope this help to fix your Honda.
GUILL....

Posted on Aug 05, 2008

  • 1779 Answers

SOURCE: interior door handle replacement 1992 honda accord

Do u mean the door latch, which u pull to open the door, or the plastic molded handle u grab to shut the door? If it's the latch, there are two small round plugs in the plastic area of the door lock and locking switch. Use a small flat end screwdriver to pry them out , exposing two philips head screws. If this isn't what u needed, let me know, I'll get more info for u. countrycurt0

Posted on Oct 04, 2008

  • 335 Answers

SOURCE: brake lock-up

I suspect that you have front disc and rear drum brakes.You did not say which of your brakes are locking up. I suggest that if your front brakes are locking {skid} that means your rear brakes are not engaging. If your rear brakes are locking {skid} then I suggest you have problems with park brake or brake fluid leaking onto the rear shoes.
More info would help me help you. I will check back soon.

Posted on May 21, 2009

ourhowse
  • 2007 Answers

SOURCE: 1996 honda accord front brakes freezing up

The most common cause would be a defective brake line. The inner lining deteriorates and acts like a one way valve, and won't allow fluid to return.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

92 accord no brakes when car first started


Hi Monroe, It sounds as if there is an air leakage into the brake system. It would be a good idea to have a look under the vehicle and discover if there is a leakage and from which wheel cylinder or cylinders. you'll be able to identify the wheel or wheels because the inside of the rim and tyre will appear wet. You will need to replace the damaged brake slave cylinder(s) which will mean a major brake rehabilitation job. If the leakage has come from the wheels, I would suggest you replace the shoes and pads at the same time. Make a drawing not a photograph. If you draw the parts you'll take more notice of the assembly and be able to reassemble more easily. You do not need a new booster! but you may need a new master cylinder in addition to the wheel cylinders. If you need to know how to bleed the brakes let me know and I'll explain. regards John

Feb 15, 2012 | 1992 Honda Accord

4 Answers

1984 Honda Accord Brake Problem


well aside from the boosters you may also want to check the possitioning rotor and calipers. there is a possibility that something slipped, or leaked, check for brake fluids and try to trace where it is comming from.

the picture below shows how to disassemble the brakes of an Accord, the only special tool you will need is a ball joint fork to seperate the upper and lower ball joints. You have to remove the whole steering knuckle assembly to get to the bolts in back of the rotor and hub assembly.

b8487ef.gif
hope this helps

Aug 05, 2008 | 1984 Honda Accord

1 Answer

Brakes r hard to press,seems like brake booster needs replacing. is it any tricks 2 changing da brake booster?


Quite a few variables here. Always is some trouble, disconnecting the brake pedal inside under the firewall, then removal of the brake resevoir, then the booster. Before you go into all that labor, did it happen gradually, then it can be a booster. If it occured suddenly, trace all the vacuum sources to the booster. It can be something as simple as a broken/open vacuum leak.

Aug 31, 2011 | 1995 Honda Accord

1 Answer

Why does my 92 honda accord make a whistle noise when i step on the brake


you have a vacuum leak in the booster drum for the power braking system

Aug 01, 2010 | 1992 Honda Accord

2 Answers

1990 honda accord hard brakepedal and I hear air leak inside car when i press on brakes


Your power brake booster has gone bad, wont hold vacum the seal has gone bad, thats why you hear air and brake pedal is hard, booster sit under hood on drivers side fire wall, master cylinder bolts up to it, replacement is the only fix, unit can not be repair.

Jan 05, 2010 | 1990 Honda Accord

2 Answers

1996 HONDA ACCORD FRONT BRAKE LOCK UP AFTER


check that the master cylinder is not locking on with a pressure build up the cyl may need replacing probly does

May 11, 2009 | 1996 Honda Accord

1 Answer

My 1992 Honda accord rotors get hot even after replacing the master cylinder,brake lines,calipers,pads. seems like the power booster is somehow the problem. like it makes the pedal get hard.


Did you bleed the brakes properly after you did all the work? Air in the system will cause varied problems, mainly, the fluid can't flow properly. Did you clean the rotors before you installed them with brake kleen? They have a rust preventive coating (like cosmoline) on them when they are new. If the pedal is hard to push the booster could be bad or not getting enough vacuum to operate properly. Take the vacuum fitting off the booster and make sure it isn't clogged. Check the vacuum line for breaks. Make sure it is connected properly. Inspect the booster for any holes.

Apr 26, 2009 | 1992 Honda Accord

1 Answer

92 Honda Accord LX


is the front (in the hood)

Mar 02, 2009 | 1992 Honda Accord

1 Answer

Excessive brake pedal travel and 'soft' brakes


the brakes have to be bleed you wrote that when you start the car the pedal goes to the floor that means the booster is working fine take it back and tell them you want the brakes bleed

Nov 14, 2008 | 2003 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

555 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...