Question about 2001 Dodge Durango

Open Question

I need to replace the oil pan on a 2001 Dodge Durango with a 4.7 liter engine. Can I do this without lifting the engine?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: p0 303 po353 codes on 2001 dodge durango 4.7 liter

did not fix problem yet going to check voltage at the 3 coil pack thank you

Posted on Jun 29, 2008

Ad
whitehorse02
  • 11 Answers

SOURCE: oil pan

Have you tried getting a screw driver and prying at it?

Posted on Oct 21, 2008

Technopro
  • 243 Answers

SOURCE: 2001 VW Passat AUG Oil Pump replacement - how to get around support beam

Best thing to do is to undo the engine mounts and lift the engine up. You can use an ond seat belt and a strong peice of wood that will fit accross the engine bay. You can use a tie-down ratchet as well to lift up the engine as it will make things easier. then you'll have more room to remove the pan. Cheers.

Posted on Nov 10, 2008

  • 82 Answers

SOURCE: 2001 dodge durango v8 4.7

It is acually called the vehicle speed sensor I do believe. It should should be located on the top of your transmission with a wiring harness attached to it. It should also have 1 bolt holding it in also. Whatever you do, do not rotate the gear when you remove it. Try to mark the exact way it came out when you replace the sensor. When you pull the sensor out it will have this gear attached to it which will need to be placed into the new sensor and put back into the vehicle in the same way it came out or you will throw a code and it will not be pretty. Good luck, hopefully I didn't scare you it can be a simple repair just mind your P's and Q's.

Posted on Jan 07, 2009

  • 1118 Answers

SOURCE: knocking in the bottom of ford 5.4 liter engine

If you hear it knocking no bearing replacement is going to fix that long term. Its best to pull it, the crank shaft will have to be turned or polished and or replaced, weather its a rod or a maine, and posibly line boared if its a maine thats knocking. Do it right and pull it.

Posted on Apr 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will i have to remove motor to replace oil pan gasket on a 2001 gmc sonoma 2.2l 5 speed


You may have to loosen the transmission also to get enough room to remove it without taking the motor out. Make sure your pan is not cracked first. Also be careful when lifting the motor as to not damage anything on top of the engine.

Nov 29, 2015 | GMC Cars & Trucks

1 Answer

How to remove oil pan on a 2004 dodge durango


You have to Unbolt the engine mounts and lift the engine, Unbolt the oil pan and rotate the crankshaft by hand to get it to clear the counterweight on the crank. If the engine has 100,000 miles or more replace the oil pump while your in there.

Dec 02, 2014 | Dodge Durango Cars & Trucks

1 Answer

Merc c 200 2003 how many liter of engine oil it will take


6 Liters of that precious oil is needed but for 2002 MB C the engine oil capacity is 6.5 liters with oil filter replacement..Need warn winches conquer any challenge without a strain. Visit the site.

Mar 04, 2013 | 2001 Dodge Dakota

1 Answer

I have a 2001 4.7 liter v8 dodge durango, the cylinders went out last year. I found a 1999 5.9 liter v8 durango engine in good condition. Will this engine match up with my mounts allowing me to use my...


You'd have to replace the transmission as well if you want to run that particular engine. The 4.7L engine is a "mod" motor and the 5.9L is the good old cast iron V-8 design.

Mar 29, 2010 | 2001 Dodge Durango

1 Answer

Im having a hard time getting the oil pan off of a 2003 Dodge Durango, 5.9 4wheel drive.


The frame is in the way and you have to lift the engine to remove the pan.
  1. Turn on the Durango and run it for at least 10 minutes, a few times around the block is best. This will get the engine oil up to temperature allowing it to drain better for you.Park the vehicle on a flat, stable surface that gives you enough room to move around under. Jack up the Durango following the directions provided with your jack and jack stands.Open the hood of the Durango and located the engine oil cap, found on the right side of the engine, towards the middle. Remove the cap by twisting it off and set aside, allowing ventilation and pressure release.Climb under the vehicle and located the oil pan. The oil pan is on the underside of the engine, between the car's tires. It is a rectangular shaped pan with a plug located on the end towards the back of the car.Place an oil drip pan under the oil pan and pull the plug by twisting it and pulling it. This will release all oil from the vehicle, draining it into the pan below. Allow the oil to drain until there is nothing left coming out.Use a wrench to loosen the bolts of the oil pan. There are a total of 17 of them located around the edge of the oil pan, connecting it to the frame of the engine. Store safely.Remove the oil pump pickup tube and oil pan gasket, which are connected to the oil pan. You will find these as soon as you drop the oil pan.
    to Replace the Oil Pan Gasket in a Dodge Durango
    1. Jack up the front of the Dodge Durango, and install a jack stand. Block the rear wheels. Remove the oil plug and let the oil drain into a pan, being sure to remove as much of the old oil as possible.Loosen the bolts holding the oil pan with a socket wrench, and remove the bolts with your fingers. Remove the oil filter, starter motor, cooler lines, oil level sensor, heated oxygen sensor connector and exhaust y-pipe, and then take off the oil pan.Scrape off the old gasket with a thin putty knife, being very careful not to scrape the surface. Be sure all of the old gasket is removed, then wipe the surface with solvent. Spread a bit of oil on the surface to promote adhesion, and apply the new gasket.Replace the oil pan, exhaust y-pipe, heated oxygen sensor connector, oil level sensor, cooler lines and starter motor, and install a new oil filter.Raise the vehicle slightly with the jack and slide out the jack stand before lowering the vehicle and removing the jacks.Fill the engine with the appropriate amount of oil. Check the level with the dipstick to be sure you have the right amount.
      this will help.thanks.

Feb 21, 2010 | 2003 Dodge Durango

1 Answer

Do I need to pull my motor in my 2001 Dodge durango to replace the oil pan gasket?


  • Jack up the front of the Dodge Durango, and install a jack stand. Block the rear wheels.
  • Remove the oil plug and let the oil drain into a pan, being sure to remove as much of the old oil as possible.
  • Loosen the bolts holding the oil pan with a socket wrench, and remove the bolts with your fingers. Remove the oil filter, starter motor, cooler lines, oil level sensor, heated oxygen sensor connector and exhaust y-pipe, and then take off the oil pan.
  • Scrape off the old gasket with a thin putty knife, being very careful not to scrape the surface. Be sure all of the old gasket is removed, then wipe the surface with solvent. Spread a bit of oil on the surface to promote adhesion, and apply the new gasket.
  • Replace the oil pan, exhaust y-pipe, heated oxygen sensor connector, oil level sensor, cooler lines and starter motor, and install a new oil filter.
  • Raise the vehicle slightly with the jack and slide out the jack stand before lowering the vehicle and removing the jacks.
  • Fill the engine with the appropriate amount of oil. Check the level with the dipstick to be sure you have the right amount.
Good luck and hope this helps.


Nov 03, 2009 | 2001 Dodge Durango

1 Answer

I need to replace the oil pan on my 2002 Dodge Intrepid with a 3.5 Liter engine. What are the steps. Especially with the metal ubber pan gasket.


1.put car on a lift. 2.Drain oil. 3.make sure to have exact oil pan ready with seal in hand. 4.unscrew the bolts in a x fashon. 1-6 3-4 2-5 remove oil pan. 4.Clean all around where the oil pan used to be. 5.Attach new seal and oil pan. hand tighten all the bolts in a X fashon then tighten with a wrench or socket. 6.make sure oil drain plug is on good. 7. put new oil in typically 5 quarts. 8.put car on ground 9. All done.

Sep 02, 2009 | 2002 Dodge Intrepid

3 Answers

How do i change the oil pump on a 99 dodge durango


disconnect battery.I believe you have to remove bolts from motor mounts,you will have to remove oil pan. you will also have to lift the motor enough to remove it.there should 2 to 4 bolts that actually hold it on.

Aug 09, 2009 | 1999 Dodge Durango

1 Answer

Do you have to lift the motor out of a 1998 dodge durango to change the oil pump


if yo can get the oil pan off completely then you will be able replace the oil pump without lifting the motor. but if you can't you will have no choice but to lift the motor.

Dec 19, 2008 | 1998 Dodge Durango

Not finding what you are looking for?
2001 Dodge Durango Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...