Question about 1995 Jeep Wrangler

1 Answer

Clutch problems. very hard to shift gears. 1995 K1500 p/u 5.0 engine. Hydraulic clutch. can it be bled ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 114 Answers

Should be able too!

Posted on Jul 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Isuzu hombre. I put a new clutch and slave cylinder in it. Can I adjust it. Is right off the floor. Hard to shift sometimes


its really a Chevy S10,
the only Japan part is the name sticker.
so what engines there?
hydraulic clutch is auto-dusting
after all air is bleed out of the system

diagnosing clutch can be bit tricky
but here are those tricks (blew many up racing)
the slave has a rod to a lever,
if bleed ok, can be hard, as the tubes go vertical
like a motorcycle or aircraft
bleeding is hard. (on all)
(bubbles float up as you force them down, dang a pain) (reverse brake bleed kit a godsend)

once done bled, i check the slave stroke distance.
its about 1 inch stoke,(2 men test)
no slack there, due to the hydraulic auto adjust.
see slack yell load, air in lines. or rod fit wrong.
so it moves about 1 full inch on the outer fork tip
PEDAL to the floor,
if yes and clutch drags, the clutch is bad.

one acid test of clutch
is REVERSE, it's a NON Syncrho mesh gear, a real gear. and fussy, (nice for testing, I learned long ago)
and will grind at the first bit, of clutch drag.
its like the coal miners canary bird, help me...

I love clutches, learned to drive in 15speed dump truck.
it had crash boxes... 5x3
double clutching all gears.all day long.

Feb 06, 2017 | Isuzu Cars & Trucks

2 Answers

Hydraulic clutch is not disengaging, when put into 1st gear the engine conks out. Replaced the master cylinder and bled the line - still conks out. Do I need too replace the slave cylinder or what?


as per your description problem not clutch since able to start in gear and drive without stall problem sounds more like a fuel delivery not the clutch

Jul 07, 2016 | Cars & Trucks

1 Answer

Hard shifting 04 hyundai accent.


Check your clutch fluid level in the clutch master cylinder's reservoir. If low add brake fluid. If very low or dry, the clutch hydraulic system should be bled to remove air in the line. Bleeding is done down at the clutch slave cylinder on the transaxle.
I would not recommend using a lighter oil. It may cause early wear of the transmission.

Jan 02, 2013 | Hyundai Motor 2004 Accent

1 Answer

Why is my gear shift so hard to move??


I believe your clutch is not disengaging fully. When this happens it may be hard to get into first gear but subsequet shifts are easier due to the fact the vehicle is moving. You probably have a hydraulic clutch system which is low on fluid or may have air in the system. Before shifting into first gear or reverse try pumping the clutch pedal 5 or 6 times then shifting, if it goes into gear easier after this then you probably have air in the system, it can be bled similar to bleeding brakes. If this doesnt work you might be low on fluid, or have a bad master or slave cylinder.

Aug 28, 2012 | 2002 Hyundai Accent

1 Answer

Thanks for your help! My 1998 Ford contour four-cylinder, five-speed manual transmission intermittently has difficulty going into reverse and first gears. The problem is intermittent. Most of the time...


You still have air trapped in teh hydrualic clutch. Bleed again and again until you get the air out. try actuating teh clutch several times fast just before you bleed it.

the clutch is partially applied, that's why it is hard to shift. the synchros can;t overcome the input shaft spinning.

Guaranteed you have air, 100%

Jan 13, 2011 | 1997 Ford Contour

1 Answer

1995 1500, 4.3 L 6, 5spd manual. Is there a


Unless this transmission was replaced with one using Hydraulic means of shifting? I know of none as a standard transmission?? Usually difficulty of shifting is because the teeth of the receiving gear is burred or broken?

Jul 14, 2010 | 1995 Chevrolet C1500

1 Answer

Hard to shift 5 speed manual speed transmission on 1995 rodeo


pending on the type of clutch in the vehicle, you may be low on clutch fluid. (if your clutch is hydraulic)
other than that it is most likely the entire clutch itself.

Jun 16, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...