Question about 2002 Jeep Grand Cherokee

1 Answer

How do you replace link bar bushes - 2002 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 49 Answers

Take it to a shop!!!!bushings need presssing

Posted on Jul 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front anti roll bar bushes


Frank, you haven't said what make or model your car is.
However, have a look on the following link - it will take you to Youtube:
how to replace anti roll bar bushes Google Search

It's not a particularly difficult job. It entails loosening the drop-links/tie bars that connect to the torsion bar - the anti roll bar, then loosening the bolts holding the anti roll bar in place.

Just be aware that the anti roll bar is in effect a 'spring' and is under tension. Loosen the retaining bolts gradually, slowly.

replacing the bushes is straight forward. Once you have removed the anti roll bar just lever the old rubber bushes out with a screwdriver and push the new ones into place .. then reassemble everything.

In the most general of terms you would do the job in a couple of hours

May 12, 2016 | Cars & Trucks

1 Answer

Replacing anti-roll bar bushes citroen xsara picasso


anti-roll bar bushes, could be the problem get a big screw driver and lever the anti roll bar see if you have movement

Jun 02, 2013 | 2001 Citroen Xsara Picasso

1 Answer

Solid bar in front end, two bushings on either side of front tires is this the sway bar?


if you are talking about the sway bar end links. you can replace them yourself to save a few bucks. first Raise the front of the vehicle with a hydraulic jack. Place jack stands under the frame on each side of the vehicle. Lower the hydraulic jack so that the weight of the vehicle is supported by the jack stands and the front wheels are off the ground. locate the sway bar end links on either side of the front sway bar. Remove the bolts from each end of the sway bar end link. replace the bushings in the same order you take them off. you can go to any auto parts store and buy end links for your car.

May 04, 2012 | 2001 Chrysler PT Cruiser

1 Answer

How do you replace sway bars on a 1995 olds 88 royale?


you will need to disconnect the sway bar from the sway bar links(in most cases you might as well replace the links as well since they may snap while trying to remove them). You will then remove the sway bar bushing caps 2 bolts on each of the 2 caps and lower the sway bar. Is the bar cracked? should not require replacing if it isn't cracked. the rubber bushings and links do wear over time and yes the bar can crack.

Feb 17, 2011 | 1995 Oldsmobile Eighty Eight

3 Answers

Safety says i need sway bar bushings.what and where are these?


the sway bar is a bar that runs acrossed the front of the van from strut to strut. It is bolted to the cradel and then has links that run from the bar to the strut to increase stability. The sway bar bushings are rubber mounts that hold the bar down to the cradel. The bar runs though the mounts one each side where the bar and the cradel meet. If they are wore out you will normally hear a clucking noise from the front end when you hit bumps. To remove and replace them there is two bolts that hold a steel cap on top of them on each side. Remove the cap from both sides then the rubber mounts will have a split in them so you can get them off the bar. To install them is just the reverse of the removal. Good luck! 4 thumbs up is appeciated if this helps.

Dec 30, 2010 | 2002 Dodge Caravan

1 Answer

Can you replace sway bar bushings or do you have to replace the whole swaybar?


YES YOU CAN CHANGE THE BUSHINGS MOST OF THE TIME ALL YOU NEED IS WHAT THEY CALL SWAY BAR LINKS IT A LONG BOLT WITH RUBBER BUSHINGS ON IT

Oct 23, 2010 | 2005 Pontiac Sunfire

1 Answer

Auto parts place says I need the rear sway bar replaced - is this the same as the links and bushings? It's a bar in the middle of the car that leads to both wheels in the rear. If it does need to be...


yes, unless the bar is broken. Are the links broken? Just replace whatever is broken or worn out. Usually the bushings under the holddown clamps and the links and/or link bushings.

Sep 13, 2010 | 2000 Buick LeSabre

1 Answer

How to replace a sway bar end links to a 94 intrepid



REMOVAL & INSTALLATION

The rear suspension on LH platform vehicles is a fully independent suspension. A stabilizer bar (also called a sway bar) is mounted in rubber isolator bushings and connects the rear struts through links. Note that the fuel tank must be removed to remove the stabilizer bar.

CAUTION OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Disconnect the negative battery cable. Relieve the fuel system pressure.
  2. Raise and safely support the vehicle.
  3. Remove both rear wheels.

  1. Position a transmission jack under the fuel tank just forward of the crossmember to help support the fuel tank when crossmember is removed.
  2. Remove the four crossmember to frame rail attaching bolts. Remove the fuel tank.
  3. Remove the stabilizer bar to link assembly attaching nuts and remove the bar and isolator bushings as an assembly from the vehicle. Inspect the isolator bushings for damage or excessive wear and replace, if necessary.

To install:
  1. Inspect for broken or distorted retainers and bushings. If bushing replacement is required, replacement bushings can be installed by locating the split in the bushing, prying open and removing the defective bushing from around the stabilizer bar.
  2. Install the stabilizer bar and isolator bushings back into the vehicle as an assembly making sure bar is centered in vehicle so it doesn't contact other suspension components.
  3. Install stabilizer bar attaching link onto stabilizer bar. Install new link to bar attaching nuts and tighten to 70 ft. lbs. (95 Nm).

Replace the sway bar bracket bolt with new after loosening or removing them. Only use original equipment bolts as replacements.
  1. Install the fuel tank back onto the vehicle.
  2. Position the crossmember on frame rails and install four mounting bolts. Tighten attaching bolts to 70 ft. lbs. (95 Nm).
  3. Remove transmission jack from under the fuel tank.
  4. Install the rear wheels and lug nuts. Tighten the lug nuts, in a star pattern sequence, to 95-100 ft. lbs. (129-135 Nm).
  5. Lower the vehicle. Reconnect the negative battery cable.
  6. Pressurize the fuel system and check for leaks.
  7. Check and reset the rear wheel toe to specifications as required.

Jul 03, 2010 | 1994 Dodge Intrepid

1 Answer

Front sway bar link kit, what is the order of installation. all my bushings are rotted away.


Remove the sway bar links from lower control arms. Replace the sway bar mount to frame bushings first. Then install sway bar link bushings. Note how they come apart and install in the same manner.

Dec 12, 2009 | 1999 Ford Expedition

3 Answers

How do i find a diagram showing my front end sway bar bushings?


The sway bar bushings are under the large clamps that hold the bar to the frame. The ends of the sway bar are connected to the struts by the sway bar links. When the links wear out, they clunk--not squeak. The bushings are under the retainer in the pic below.

0996b43f80231399-sulc2cgngkoxge0rocse0fez-3-0.gif

Aug 06, 2017 | 2000 Dodge Dakota Quad Cab

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...