Question about 1988 Ford F 150

1 Answer

Stops runing but starts right back up 88 ford f

I have a 1988 ford f 150. starts up fine when i put in gear it will stall a few tims then it will be fine> but at time it will just completly shut of but continues to start right up. I was thinging of replacing the ignation switch fuel filter module and the coil

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Have seen this before,these vehicles have a history with fuel pump relays failing,also idle air valves getting carboned up (dirty inside) and idle air is restricted and engine dies,and ck map sensor vacuum tubing for cracks.good luck

Posted on Jul 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It did not stall i stop put in park with motor runing put it back in drive and it would not go back into drive why


Sounds like no transmission fluid. Check the fluid level for your transmission, there should be a seperate dipstick

Aug 31, 2014 | 2003 Ford Windstar

1 Answer

I have 88 fullsize bronco with 351w and c6 trans, when i start it runs fine till i put it into gear it stalls and won't start till it sits for a while, before this happened my engine temp gauge was jumping...


Check all your grounds. Behind the right cylinder head, on right lower front of block and engine to frame. Also check fuse links at starter solenoid.

Oct 27, 2017 | Ford Bronco Cars & Trucks

1 Answer

Hi Folks, My 99 crown vic has an intermittent stalling issue. I can be driving along and it just cuts out (usually, not always, when I take my foot off the gas). It will start right up at first and...


Was the fuel pump checked out?
Have a scope put on it,to check for a worn armature. May also be binding up mechanically
Also check TPS Sensor data or scope it

Nov 03, 2010 | 1999 Ford Crown Victoria

2 Answers

Vibration when in gear, and stalling.


The problem is the torque converter solenoid. I had it happen on my 94 Cavalier a few years back and was a cheap fix at the local car mechanic. What happens is the transmission warms up and hits a certain speed where the solenoid engages, but then it sticks and won't disengage until it cools down sufficiently. When it sticks, it causes the car to shake when slowing down and will snub out the engine if you come to a stop.

Mar 09, 2009 | 1994 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...