Question about 2006 Jeep Commander

Open Question

How much does it cost to fix lifters on a 2006 jeep commander

Posted by on

  • BrianWren Jul 07, 2010

    What exactly do you mean by ?fix? the lifters?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

Ad
  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

Gozer
  • 435 Answers

SOURCE: install a altenator for a 2006 jeep commander

I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

Posted on May 21, 2010

alicantecoli
  • 22156 Answers

SOURCE: 2006 Jeep Commander inefficient catalyst

most likely the oxygen sensors (lambada) ,they need changing ,their are two one before the cat and one after,do not think you need a new cat unless it has a min of 150.000 miles on the clock

Posted on Jul 02, 2010

weekspena
  • 375 Answers

SOURCE: 2006 jeep commander blower will not blow at all

First check all of your fuses under hood and under dash! If they are all good you need to get a new blower motor, you can get one at your local autozone, orileys, etc. not that hard to change out. should fix you right up!

Posted on Jan 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bas/esp light is on inmy jeep commander 2006


This video is for a liberty, but all Jeeps should be similiar.
Jeep Liberty How to fix Traction ABS EST Light Codes C1240 C123F Also a guy in a forum says that it might involve a recall of the DCX recall applying to ABS modules on many Chrysler, Dodge, & Jeep products including the Commander. I'd call your dealer and ask, they might fix it for free if it's a recall. http://www.jeepcommander.com/forums/5-general-commander-discussion/1483-esp-bas-traction-control-light-staying.html

Nov 17, 2016 | Jeep Cars & Trucks

2 Answers

2006 jeep commander electronic range selector not working


google cleaning jeep grand cherokee shifter module its the same thing
or google grand cherokee or commander forums find a few and post this and all future questions there
if you are speaking of all the shift positions being surounded by brackets like [r] [n] [d] [l] than thats likely the problem the part can be cleaned its located beneath the shifter bezel or replace it the part is about 450 to 500 bucks but try the foorums i know ive seen a writeup with pictures there

Feb 03, 2013 | 2006 Jeep Commander

1 Answer

Warning lights go on and off....2006 jeep commander


that code means the computers are not communicating

Aug 21, 2012 | 2006 Jeep Commander

3 Answers

2006 jeep commander blower will not blow at all how to test or fix problem


First check all of your fuses under hood and under dash! If they are all good you need to get a new blower motor, you can get one at your local autozone, orileys, etc. not that hard to change out. should fix you right up!

Jan 10, 2011 | 2006 Jeep Commander

1 Answer

2006 jeep commander check engine light stays on after jeep sat for 5 days in ice storm and was not started


I don't think I would be concerned about the vehicle sitting for 5 days. Get it scanned and work on a fix,for why the light came on.

Feb 15, 2010 | 2006 Jeep Commander

1 Answer

Ac/heater fan switch problem on a 2006 jeep commander


next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Feb 13, 2010 | Jeep Commander Cars & Trucks

2 Answers

Jeep commander clicks once and won't start. It is


The starting issue is the same I had on my 2005 Grand Cherokee. The wire coming from the ignition (key area) to the Starter the connection is bad. The shop replaced the lead and it is perfectly fine... it cost $70. I dont know the techincal terms.. but it was easy to fix- the problem is water and junk gets splashed up by the front tire and corroded the wire into the sarter.... that's all it was.
Good luck.

Sep 05, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...