Question about Cars & Trucks

1 Answer

My heater comes on when its switched to the third position or forth and does work on the first or second position how can i resolve this problem.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 819 Answers

Unfortunately you did not provide the year make and model for your vehicle, so i cannot provide specifics.

nearly all cars now have a part called a "blower motor resistor". they are almost universally found in the ductwork near the blower motor, typically on the passenger side underneath the dash or behind the glovebox. these are a common failure, and are readily available at most parts suppliers. good luck!

Posted on Jul 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Any ideas why a 1998 Mercury Grand Marquis would just suddenly stop running in the middle of the highway going 55 mph and w a half tank of gas in it and now turns over but wont actually start again?


first suggestion is broken timing belt
second is failed crank shaft position sensor
third is failed cam shaft position sensor
forth is failed ignition control module
fifth is faulty ECM or power fuses to the ignition, ecm

Mar 23, 2017 | 1998 Mercury Grand Marquis

1 Answer

Half of the engine not firing


If half the engine isn't firing, it may need a new coil pack. Most v6 and v8 engines have a coil pack for each side of the engine. Try swapping them around to see if the other side works; then you'll know. If it's not a coil pack, it's because your car has variable cylinder management, and it has electronics issue.

May 09, 2017 | Cars & Trucks

1 Answer

How to program a bcm on a 2000 buick century


You can program it with or without a scan tool
Without a scan tool.This procedure will take 30 minutes.So make sure battery is fully charged 1.Turn the ignition switch off.2. Turn the ignition switch all the way from the off to the start position , then leave it in the on position. Note: The engine will not crank,3. The security light will come on and stay on for at least 10 minutes. 4. Turn the ignition switch off for five seconds. 5.repeat steps 2,3 and 4 again for a second time. 6. Repeat steps 2,3 and 4 again for a third time. 7. Turn the ignition switch off. 8. Turn the ignition switch all the way to the start position .The engine should now start. 9. Check BCM for any codes

Mar 06, 2012 | Cars & Trucks

1 Answer

How to seat fuel injecters


Assuming the injectors are already installed in the fuel rail, put a little fuel on the injector seals, position the injector rail in front of the holes in the head.
Start from one end of the rail and work the first injector into its hole a little bit, but not all the way. then do the same for the second and third. Work them in a little at a time so the injectors dont come loose from the fuel rail.
Once you get all injectors completely into the holes, rotate each of them back and forth until the injector turns smoothly when you rotate it. Once an injector rotates smoothly its seated correctly. But only rotate them a small amount back and forth.
If the injectors are removed from the fuel rail, do it the same way. Just install them in the fuel rail first, then install the rail/injectors into the cylinder head.

Sep 26, 2011 | 1995 Oldsmobile Cutlass Ciera

2 Answers

How to change cabin air filter?


Place the ignition switch in the Off position, remove the supplemental inflatable restraint fuse from the rear fuse panel. On 1997 models, the rear fuse panel is located in the luggage compartment. On the 1998-2003 models, the rear fuse panel is located under the rear seat. Remove the two retaining screws from the rear edge of the left sound
insulator. Push in on the snap tabs to release the insulator. Disconnect the left sound insulator electrical connectors, then remove the insulator. Twist the shift cable grommet and position away from the cabin air filter access door. It may be necessary to cut the tie strap and peel back the foam insulation to position the grommet away from the door. Remove the cabin air filter access cover from the A/C and heater module.

Remove the tape, then pull out the first cabin air filter element using the filter tab. Remove the tape, then pull out the second cabin air filter element using the filter tab. Remove the tape, then pull out the third cabin air filter element using the filter tab.

To ease installation, lubricate the new filter guides with silicon spray. Install the first clean air filter into the case. Using a long thin blade screw driver and filter tab, raise the filter until it is parallel with the A/C and heater module. Ensure the leading edge of the filter engages the filter case holding rib. Engage the new second cabin air filter in the tab of the first filter. Slide the second filter into the remaining channels of the first filter. Using the filter tab, raise the filter until it is parallel
with the A/C and heater module. Ensure the leading edge of the filter engages the filter case holding rib. Engage the third new cabin air filter in the tab of the second filter. Slide the third filter into the remaining channels of the second filter. Fold the tab of the second filter down. Fold the tab of the third filter up and over the second filter.

Install the A/C and heater module filter cover. Ensure the cover is properly seated. position the shift cable grommet. Position the left sound insulator to the instrument panel, then connect the electrical connectors. Install the left sound insulator fasteners. Torque the fasteners to 18 inch lbs. Be sure to install the fasteners in the proper locations, then install the SIR fuse. From a position off to the side of the air bag module, place the ignition switch in the "On" position. The air bag warning lamp should flash 7 times and then turn Off. Place the ignition switch in the "Off" position.


898aa74.gif

Jun 22, 2010 | 1999 Cadillac Seville

1 Answer

Heater in 1993 Yukon quit working


check fuse first,
switch second,
blower motor resistor third,
blower motor last

Dec 27, 2009 | 1993 GMC Yukon

1 Answer

My new 2010 Toyota Sienna XLE Ltd daytime running lights (DRL) do not seem to come on in any position of light switch on stalk. Light came on in older Siennas (2004) whenever van was started regardless of...


first, your vehicle is under factory warranty so I wouldn't play with anything. Second make sure that the emergency brake is completly off, third some vehicle drl systems only work when the vehicle is taken out of park. I hope this helps.

Dec 25, 2009 | 2009 Toyota Sienna

1 Answer

25A heater fuse keeps blowing on Suzuki x90


it sounds like something is shorting out for the fan switch. I would take the dash apart and take a look to see if one of the wires is burnt and shorting out the fan switch. This is most likely the case.

Oct 21, 2008 | 1996 Suzuki X-90

1 Answer

Automatic transmission problem


May be the Throttle Position Sensor. Normally the check engine light will come on when this happens.

Sep 05, 2008 | 2000 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...