Question about Land Rover Range Rover

1 Answer

2004 range rover with the code P0730 stall speed fault safe mode the code says faulty trans (mechanical) or bus can communication the car drives fine with no hesitation or jumps or noises anything just fine all gear change until the car engine gets to normal operating temperature. and only if you get to a light or stop then the car goes on neutral and the trans goes in to safe mode. stop the car cool it start it again and it will drive fine until temperature is again normal . any ideas?

Posted by on

  • Fausto Artiaga
    Fausto Artiaga Jul 06, 2010

    yes
    very to the point and accurate
    thank you

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Land Rover Expert
  • 1,868 Answers

Hello! When the problem occurs Try backing up...If there is not a problem then Transmission clutch "A" is at fault...A known vulnerable point is the snap ring that retains the A clutch pack...Increasing fluid temp. causes leakage and pressure to drop...Dumping the clutch and putting you in neutral...

Major rebuild...

Guru..............saailer

Posted on Jul 06, 2010

  • Fausto Artiaga
    Fausto Artiaga Jul 06, 2010

    thanks
    that is no problems with reverse even when is hot.
    replace trans?


    thank you very much.

  • David Burbee
    David Burbee Jul 07, 2010

    Hello! Replace or re-build? I would have it re-built...............Saailer

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 04 Range Rover goes into lock down eventually it starts what's the fault


You must have the system scanned to locate the fault, it will present a fault code.

Apr 13, 2016 | 2004 Land Rover Range Rover

1 Answer

Error Code U0019 on a HYUNDAI SANTA FE MODEL YEAR 2004 ENGINE : DIESEL


Code meanning low speed can communication bus not sure what that is

Apr 09, 2015 | 2004 Hyundai Santa Fe

1 Answer

Range rover 2006 sport diesel auto trans not shifting in D mode only shift in triptonic I change trans control module but its showing u3000 code now what to do?


the transmission control module has to be programmed to the vehicle using suitable diagnostic equipment. the code you have got i suspect is telling you that, all the modules on modern vehicles communicate with each other via. the can and scp networks to work correctly. if that has not been done, that is more than likely the problem, or the road speed signal may be missing but i suspect you would have other fault codes logged. hope this helps. ps. i worked for a jaguar franchise before i retired, they use the same systems, same company.

Mar 17, 2015 | 2006 Land Rover Range Rover Sport

1 Answer

How i fix the p0730 and p0735 in range rover 2006


Possible causes of OBD code P0730
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Shift solenoids harness or connectors - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: The TCM has detected that the transmission is trying to mechanically shift to a lower gear than intended

Possible causes of OBD code P0735
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: P0735 is detected when A/T cannot be shifted to the 5th gear position even if electrical circuit is good.

Dec 24, 2014 | 2006 Land Rover Range Rover

1 Answer

Speed signal n-ab(output)


the fault code is 32 speed signal n-ab output

Sep 25, 2013 | 2004 Land Rover Range Rover

1 Answer

Range rove 2004 is in engine failsafe mode is not starting?


You need an owners manual or access to factory
manuals to find out how many fail safes your vehicle has

Example: Electronic Throttle Control
Engine Over Temp
Transmission Failsafe
Misfire Fail safe to protect converter

Once you have checked for codes which I assume you have
done long ago,you use them as well as trouble charts to
diagnose things

Mar 29, 2013 | 2004 Land Rover Range Rover

1 Answer

Am receiving a message on my Range Rover 2004 Inactive suspension


Welcome to Fixya

Air suspension is currently in fault mode. It will have to be re-set by someone who has the Land Rover scantool (either a dealer or an independent shop). The EAS system is inaccessible with a regular OBDII scantool. The car will not allow you to control the suspension height (raise/lower/defeat) until the fault is cleared. Please see this link .

Thank you for using Fixya!

Apr 07, 2011 | 2004 Land Rover Range Rover

1 Answer

Have a 2004 range rover with p122b code output speed sensor. Replaced sensor and checked wiring in transmission and going to control unit. Did a transmission service, flush and filter. You can drive all...


This might sound odd, but it could be the gearbox output shaft bearing. If the transmission sounds noisier than it did, this could be the issue. Only way to check is to take off the transfer box. Not a major job, but takes a while. Some good fault code readers will read transmission codes, and allow you to see in real time what the sensor is doing - if the sensor suddenly loses signal, then it is very likely to be the a bearing (output shaft bearing most likely) that is at fault, causing the sensor ring to move too far from the sensor. Best guess, but could be other things, so don't go taking that transfer box off without getting a road test with a good fault code reader on it - or find someone with a portable oscilloscope and put that across the sensor - you should be able to see nice square wave pulses - if they get bigger and smaller (variable amplitude), that's your problem. If not, the fault lies elsewhere.

Jul 22, 2009 | Land Rover Range Rover Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

762 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...