Question about 1996 Jeep Cherokee

Open Question

I have a 1996 Jeep Cherokee and the flashers and turn signals have stopped working. The hazards are now working when I replaced a blown fuse but there is nothing for the signals still. I have runing lights, head lights, and all the fuses are fine. I noticed the hazard relay was VERY hot under the steering column when I checked it out, does that change anything?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

thutson66
  • 96 Answers

SOURCE: turn signals and hazard flashers quit working

There are two possible locations for the relay.

First in the fuse panel, close to the bottom.

Second, in some models they put the darn thing behind the dash in the center of the car, it's a real pain to get to if it's that one.

Good luck

Posted on Aug 05, 2008

  • 958 Answers

SOURCE: Hazard Flashers, turn signals and brake lights quit working

please check your flasher relay. it is normally a three prong relay box.


tnx 4 using fixya,

drcool

Posted on Sep 02, 2008

  • 99 Answers

SOURCE: turn signals don't work

you should have a flasher for the turn signals as well as one for the hazard flashers turn signal flasher can be in fuse box on drivers side or mounted to steering column

Posted on Nov 30, 2008

motor1258
  • 6674 Answers

SOURCE: I need a diagram as

Have a look down by steering column near where diagnostic connector is.

Posted on Jan 11, 2009

  • 73 Answers

SOURCE: 99 jeep cherokee Blinker problem

Hi Bill,I think before replacing anything else you should give that hazard switch a good workout.The switch doesn't get get used very often and the contacts get corroded and can upset the indicators.Good Luck.

Posted on May 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 jeep grand cherokee is maKing a buzzing noise by the fuse box and only goes away when I turn my hazards or turning signal on


There's a relay/flasher that sounds like it may be dying. There are actually two of these in your Cherokee - round plug piece about an inch tall that plugs into your fuse block.

The good news these are cheap (less than $10 online). I'd try replacing the turn signal flasher with a new one and see if the noise goes away.

May 10, 2015 | 1996 Jeep Grand Cherokee

1 Answer

My 99 jeep cherokee turn signals and hazards ARE NOT WORKING.everything else works fine.it dnt even make the clicking noise like it should.the fuses are fine.wut else could it be?


You'll need to locate your "turn signal flasher" and replace it. You'll find it in either of the 2 fuse boxes, the owner's manual will have it listed. They are usually a small square box with 2 or 3 electrical prongs that just unplug and plug back into the slots. Please rate this answer, thanks.

Feb 01, 2011 | 1996 Jeep Cherokee

2 Answers

My turn signals have stopped working on my 1996 Dodge Ram truck, the hazard flasher is still working, I checked the fuses & they are not blown....what do I do?


check the bulbs and sockets they plug into then i would check any ground wires going to or coming from the turn signals i would also check the turn signal switch for any broken parts the hazard flasher is also the same flasher that runs the turn signals so there pretty cheap.

Dec 13, 2010 | 1996 Dodge Dakota

1 Answer

Where is the flasher located


1996 Jeep Grand Cherokee 4WD 4.0L MFI 6cyl:
The Flasher is located front seating area, driver side, under dash, driver side of steering column, mounted in convenience center.
Application:
- Hazard flasher
- Turn signal

Check the ZJ-Secc-8W-Wiring-Diagrams (page 8) for Convince Center graphics.

I really hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Hazards and signals don't work


you need a new flasher it'll be in the fuse box

Oct 19, 2009 | 1999 Jeep Cherokee

2 Answers

Turn signals, hazards not working


Mine just went out this past week and found the flasher/hazard fuse inside the glove compartment under the plate with the pull cord to access.The 1994 Jeep Grand Cherokee Laredo AWD part# on the fuse and called to confirm with a Jeep dealer is:
56007243 and appx. 44.00 from the dealer, may be able to get from an auto store as well.

Good luck if it is the fuse box you were looking for.

Aug 09, 2009 | 1994 Jeep Grand Cherokee

2 Answers

I need a fuse panel diagram to replace the turn signal flasher. Thanks


Before replacing the flasher does the hazards work, Try wiggling the turn signal lever up and down and back and forth with the key on and the lever in each position. If the blinkers or hazards start flashing you'l need a multifuntion switch. This isnt a definative test if you get nothing you may have a blown fuse. As fas as the flasher goes, go buy one and then you will know what it looks like.

Jul 14, 2009 | 1998 Jeep Cherokee

2 Answers

Turn signals and hazards won't work on my 1997 Jeep Cherokee


under the hood of the vehicle there is another fuse/relay box, locate the signal flasher and try replacing that.

May 04, 2009 | 1997 Jeep Cherokee

1 Answer

1996 jeep cherokee help plz


the circle three prong fuse is the turnsignal flasher and that very well could be the problem. does the signals come on and then not flash or does the signals not come on at all?

Feb 26, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Hazard Flashers, turn signals and brake lights quit working


please check your flasher relay. it is normally a three prong relay box.


tnx 4 using fixya,

drcool

Sep 02, 2008 | 1996 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...