Question about 1995 Chevrolet K1500

Open Question

Wiring instructions for kelsy 10958001 controller

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Model 20070910 cannot control temperature gets to hot

Hello Kitty,

Go back to your assembly instructions where it shows to connect the INTERNAL WIRE FROM YOUR Masterbuilt to the
"CONTROL PANEL"... (remove panel from body to check)

See instructions

If THAT wire is connected the next instruction for
UNCONTROLLED HEAT... is to CALL Masterbuilt...
For Assembly Assistance, Missing or Damaged Parts Call: MASTERBUILT Customer Service at 1-800-489-1581

Hope this helps.

Carnac the Magnificent

Nov 28, 2017 | Cars & Trucks

1 Answer

How do I wire a brake control unit into mitsubishi magna V6 auto?

the unit you buy will have the instructions for getting a 12 volt feed from the fuse box (never direct of the battery has to have a fuse )
the unit slide controller will be near the driver side and a 12 volt wire will run through that controller inside the car to the back of the car to the trailer plug connection matching up with the wires to the trailer/caravan horse float .electric brakes

Aug 29, 2014 | Mitsubishi Magna Cars & Trucks

1 Answer

How do I add Cruise control on a 1.8 sri 60 plate

When you buy the cruse control all the wireing should come with it plus instructions

Mar 29, 2014 | 2010 Opel Zafira 1.8

1 Answer

Mini one wing mirror

Most car breakers yards will have one,mirror included,an extra couple of quid and they will fit it for you. A lot cheaper than going to a dealer.

Jan 23, 2014 | Cars & Trucks

1 Answer

I need a wiring diagram to install, hard wire a brake controller Ford 1991 E350 van. Where to start looking for wires in cab area?

It all depends on the instructions that come with your brake controller. In 1991, the wiring diagrams published by the manufacturer were not real good at indicating locations of things. For most brake controllers, you only need to use the output side of the brake lamp switch, a direct battery positive circuit (Which would be best to run directly to the battery with an inline fuse), an "ignition" hot wire (which there is probably a connector in the underdash fuse block that is marked "fused Ignition" - there should be one right next to fuse # 14). And the wire that must be run to the back of the vehicle to the trailer connector.
It is really very simple and you should not need wiring diagrams to figure it out...just the instructions with your controller.

May 18, 2012 | 2004 Ford E-350 Super

2 Answers

Where is the abs control module on a 2000 chevy blazer LS 6cyl 4.3 L

i think it is under the hood . drivers side on the fender well near the master cylinder. should be a big sliver box with brake lines coming into it and out of it . The BCM or abs module is the littler black box screw down on top of this and should have Kelsy hazes stamp on the cover on it

Mar 06, 2011 | 2000 Chevrolet Blazer

1 Answer

Where is the pcm on a 1999 ford taurus

The PCM is located behind the engine on the passenger side of the car, it is in a slot in the fire wall behind the cowl cover. here is Fords instructions for replacing it.Powertrain Control Module (PCM)

Disconnect battery ground cable (14301) . Refer to Section 14-01.

Remove cowl deflector.

Remove screw securing the ground cable of the engine control sensor wiring (12A581) to the dash panel (01610) .

Loosen engine control sensor wiring to PCM connector retainer bolt.

Remove engine control sensor wiring from PCM (12A650) .

Remove retaining nuts and powertrain control module insulator from dash panel .

Remove powertrain control module .


Follow removal procedure in reverse order.

Tighten insulator retaining nuts to 8-12 Nm (71-106 lb-in).

Tighten engine control sensor wiring retainer bolt to 3.7 Nm (33 lb-in).

Tighten engine control sensor wiring ground retaining screw securely.


Dec 28, 2010 | 1999 Ford Taurus

1 Answer

How do you install a brake controler for a towing package?

Alot of these trucks have the wiring hook up under the dash or at rear bumper area where you can just plug the wire harness from controler to it, but if not they are simple to wire and then you must level by following the instructions,you would wire it to power and ground then one wire to brake switch and the last wire goes to tow connector for electric brake on the trailer. for more help google how to install brake controller there you will find wiring diagrams and videos.

Oct 08, 2010 | 2008 Honda Ridgeline

2 Answers

Power wire for brake stop switch? I'm adding an electric brake controll and need to know which wire has power when the brakes are pushed? There's about6 going into switch

to do this you need a twelve volt tester ground one of tester and test the wire on brake switch and u will find the right wire

Jul 07, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Chevrolet K1500 Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides