Question about 2005 Ford Taurus

Open Question

Can't locate where to put brake fluid for a 2005 ford taurus

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Monster80
  • 460 Answers

SOURCE: What is the location of the PCV valve on a 2005

Its in the back of the intake.It points straight towards the windshield way.It has a black hose that comes off from it..If your standing in front of the car looking down at the motor at the middle of the motor look straight back and down just after the intake starts to round down you'll see it..

Posted on Mar 30, 2009

Ad
ZJLimited
  • 17970 Answers

SOURCE: Location of the Horn Relay on a 2005 Ford Taurus

In the checkthe Cavity 38, Fuse 15A for Horn, Diagnostic Connector (ODB II).

Also can review the 2005 Ford Taurus - Owners Manual (page 178, Fuse Description).

56dd6cb.gif

Hope helps with this (reemmber rated this help). Good luck.

Posted on Jan 12, 2010

mitchbtu
  • 121 Answers

SOURCE: Where is pcv valve located on 2005 taurus

It is below the egr valve close to the intake manifold below the intake air sensor, there is a tube running to it from the engine to recirculate exhaust air with fresh air, there is a clamp holding it to the air intake that you need pliers to remove, then you need to turn counter-clockwise 90 degrees to remove, do the reverse to install. to make it easier to access remove the upper intake. The pcv valve is not visible, however, you can identify it by the 3" inch long rubber hose that connects to the steel line running into the bottom of the intake. I have the part and am going to replace it soon, although Ford really makes it difficult to remove it -
pcv valve is located just under the throttle body. remove air cleaner assembly from throttle body and you will see a u shaped hose running horizontally.

Posted on Jan 27, 2010

fordfixer
  • 58 Answers

SOURCE: leaking brake fluid from rear driver side brake

They don't make diagrams for brake lines. The lines are sold in bulk. You need to measure and duplicate the bends in the orignal lines and cut/flare the lines yourself. You will need a tubing cutter, flare tool and tubing bender.

Posted on Feb 27, 2010

  • 548 Answers

SOURCE: brake fluid low warning came on in 2004 Ford

Whoa, there is a line marked on the fluid reservoir that you do not fill above. Be careful to make sure that you don't get dust/debris inside the reservoir. The owners manual and the reservoir have markings to tell you what type of fluid should be used.

Posted on Sep 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will happen if i put a little power steering fluid in the brake fluid companetin 1996 ford taurus


nothing its a lighter viscosity fluid but i would get the lines flushed

Jan 20, 2013 | 1996 Ford Taurus

1 Answer

Where does brake fluid go


Open the bonnet. Locate the thin brake pipes. Trace them back to the cap where you put brake fluid in. Usually close to the windscreen side of the engine infront of the brake servo which looks like a giant disc

Oct 15, 2012 | 2001 Ford Taurus

1 Answer

I need to add brake fluid. Does the car have to be warm or can I do it when it is cold?


You can add brake fluid when its cold just make sure you are adding the right fluid most vehicals take DOT 3 brake fluid, look inside your owners manual in the recommended fluids and lubricants section and make sure thats the right brake fluid for your ford......

Dec 07, 2010 | 2005 Ford Taurus

1 Answer

What maintenance should be done for a 2005 ford taurus with 60,000 miles?


Change engine oil and replace oil filter.

Inspect tires for wear and rotate.

Inspect brake pads/shoes/rotors/drums, brake

lines & hoses, and parking brake system.

Inspect wheel ends for endplay and noise.

Inspect engine cooling system and hoses.

Inspect exhaust system and heat shields.

Inspect steering linkage, ball joints, suspension

and, if equipped, half shafts, driveshaft and

U-joints.

Replace engine air filter.

Replace fuel filter..

Replace cabin air filter, if equipped.

Change automatic transmission fluid on vehicles

equipped with the Torqshift and 4R100

transmissions. Replace the remote filter element

on the vehicles equipped with the Torqshift

transmission. Inspect automatic

transmission/transaxle fluid level on all other

vehicles, if equipped with dipstick. Consult your

dealer for your particular requirements.

Change automatic transaxle fluid and filter on all
vehicles equipped with CVT.

Nov 16, 2010 | 2005 Ford Taurus

1 Answer

I replaced my brake pads & rotors but now i have no brakes


Assuming you put everything together correctly, you may have let air in the system. Follow the brake bleeding procedure for your car. Becareful with ABS systems the fluid can be under very high pressure. Get pro help if you don't know how.

Sep 14, 2010 | 2005 Ford Taurus

1 Answer

How much brake fluid should I put in my 2005 Taurus


There should be a fill line but if you don't see it you can fill it to where you think the bottom of the cap would be when it is replace. It really doesn't matter how full it is you just don't want it spilling out when you replace the cap. As your brakes wear down it takes more and more oil to push the brake pad out to the rotor. That's the reason your brake fluid is low.

Dec 05, 2009 | 2005 Ford Taurus

1 Answer

How do i bleed the brakes on a 2005 taurus


2 Ways 1 pressure bleed ,,thats with a pressure pump full of brake fluid and undo bleeding nipples one at a time OR the other way 1 person in car 1person filling tank with b/fluid while you get under car a open bleeding nipples 1 at a time starting at the L/H/F then when only fluid cones out lock it up and to R/H/F and then to rear ,,but when open pedal down ,put your finger over nipple so no air goes when pedal is let up and so on..

Oct 02, 2009 | 2004 Ford Taurus

1 Answer

Brake light


have you looked at the connectors? for the electrics

Mar 20, 2009 | 2005 Ford Taurus

1 Answer

Changing Brake Fluid


yes, it is quite simple actually

check out the following website for videos on what to do which is much easier to see than me telling you what to do.

http://www.expertvillage.com/video-series/1157_brake-fluid-change.htm

May 14, 2008 | 2005 Ford Taurus

Not finding what you are looking for?
2005 Ford Taurus Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...