Question about 1996 Ford Explorer

1 Answer

I HAVE SEVEN EMISSION CODES THAT NEED SOLVING I CAN DRIVE THE CAR BUT AFTER A FEW MILES IT STARTS STALLING AND WILL SHUT OFF ON ME. IF I WAIT A HALF HOUR OR SO I CAN GET IT TO START A GAIN . ITS LIKE WHEN I PUT MY FEET ON THE GAS PEDAL THE PRESSURE IS TO WEAK TO GIVE IT THE POWER IT NEEDS TO DRIVE

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

First things first. 1. Get the codes from the system. 2. ahve the fuel pressure tested. 3. check the fuel filter(replace as necessary). This sounds like you have a bad MAF(mass air flow sensor). Check these items and let me know.

Posted on Jul 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I start my car it runs rough and wants to shut off, the little wrench is on, I then disconnect the battery to reprogram the computer and drive it, gets better. Day later same thing happens again.


You cannot just reset the computer to clear the warning lights! You need to connect the OBD code reader and read the codes that will determine the problems you are having! When you have the codes post them here and we can assess your problem!

Sep 09, 2015 | 2005 Ford Thunderbird

1 Answer

Car is stalling and jerking randomly


ok, first thing I need too ask is..Whats the make model and year of your car?

Mar 20, 2014 | Cars & Trucks

1 Answer

After driving my 2007 honda pilot for about 25 to 30 miles the engine light comes on then VSA light comes on then I lose power.SO I shut it off the car & have to wait a while then I can drive a li


Why did you not leave the vehicle at a repair shop or dealer
to be properly diagnosed & repaired

Any time you get any dash light on after the motor is running I
check for codes that day & get on with the required checking
& resolving within days or use another vehicle

You should stop using a vehicle with check lights & faults
& forget the free codes checks at the parts stores


Always use a professional scan tool & look at all data real time
generic & enhanced something a code read won't do & go for
a long road test with the scan along

Cylinder misfires will ruin an expensive exhaust converter
as will vacuum leaks,leaking injectors etc.

Today's vehicles need to be 100% or parked or you create
problems,do damage,run up your repair costs & shorten the
life of the vehicle all thanks to the Govt Emission non-sense

Mar 10, 2014 | 2007 Honda Pilot

1 Answer

Car starts ok when cold but acts like it is flooded when warm


Is the check engine light on while you're cranking the engine?

Jul 27, 2017 | 1998 Ford Taurus

1 Answer

After driving four to seven miles engine light comes on.when I shut off the car engine light goes off till I drive four to seven miles


Go to Autozone or Oreillys for a free scan. If done within 20 to 25 startups whatever happened will be recorded and in memory.

When you replace parts remember to disconnect the NEG cable of the battery for 10 minutes to clear the old problem. The codes will show you what area is messing up.

May 19, 2010 | Cars & Trucks

1 Answer

I cannot inspect my car because it reads is not ready yet. I used a actron code reader and I had one code that turn out to be the ox sensor by cat. I changed it. When I went back to autozone to get codes...


Basically take the car for a long drive .
Stop off get gas , drive to a shopping center( need a few on/ off starts). Few hard braking , few not so hard braking. reverse when possible . Gotta figure about 30- 50 miles of driving.

May 10, 2010 | 2002 Mazda Protege

1 Answer

Running and stalling


i would look into the EGR valve that is usally the problem.

Jan 30, 2009 | 2000 Dodge Neon

1 Answer

Stalling on a 22re engine


hi voltage sistem is overheting (vovina) chench it

Nov 03, 2008 | 1985 Toyota Celica

Not finding what you are looking for?
1996 Ford Explorer Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...