Question about 1998 Dodge Dakota

1 Answer

No clutch pedal has new master cylinder & slave cylinder still no pedal.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

You have air in your hydraulic line. Needs bleeding. If it uses one,
make sure that you used a new crush washer where the line attaches to the slave. Tie a rope around the pedal and use that to pull it back out after pressing down. Makes the process a bit easier on your assistant.

Posted on Jul 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parts diagram for clutch slave cylinder nissan D40


It's easy put new master cylinder in place but don't connect rod to clutch pedal or bolt it to bulk head and leave metal solace feed pipe undone , connect fluid feed pipe to cylinder then tilt cylinder so slsve out let faces more down wards then top up fluid pot when fluid runs out slave outlet reconnect slave pipe , bolts master cylinder back in place and connect pedal to it , then undo nipple on slave cylinder let fluid run out freely titghten niplle then pump clutch pedal until it becomes firm job done .
15 minute job .

Nov 07, 2015 | 2007 Nissan Navara 2.5

1 Answer

Clutch master cylinder low on fluid is it a sign off a bigger problem???


Only if it has a leak somewhere. Not that many places to check. Sometimes the master will leak, and you will have brake fluid below the clutch pedal.
A single steel line runs from master to the slave cylinder, down on the transmission bell housing. Check the line and the slave cylinder for leaks. If the slave is leaking, probably need a new one. And same for the master cylinder.
Fill the reservoir and check clutch operation. If any air got in the line to the slave, you will have to bleed the slave at the bleeder valve there. They are bled just like brakes, using the clutch pedal.

Dec 10, 2013 | 1996 GMC Sonoma

2 Answers

I have 94 Mazda mx-3 for the past month or so I've been having problems with my clutch and I notice a big wet stain on the floor mat and carpet I assume its the master cylinder or slave cylinder but I am...


It's leaking on the driver's side? That would be the master cylinder bolted onto the firewall. You will have to replace with a new or remanufactured clutch master cylinder. When the seals go out, the whole unit must be rebuilt. The store will give you a discount if you bring in your old one for exchange.
The clutch slave cylinder will be down on the transmission bell housing. Follow the small steel line from the master cylinder. It goes right to the slave cylinder.
Pretty easy to change out the master cylinder. Remove the steel line, unbolt unit from the firewall, then under the dash, there's a rod from the clutch pedal to the master cylinder. Just undo the retaining clip or pin holding the rod to the pedal. When the new unit is installed and filled with fluid, then you get to learn how to bleed the hydraulic clutch at the slave cylinder-the fun never stops.

Oct 31, 2013 | Cars & Trucks

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

2 Answers

I have changed the clutch master cylinder and the slave cylinder, but still don't have pedal, we have bleed the lines and checked for leaks, no leaks were found. The new slave cylinder doesn't seem to be...


Thn the problem is the clutch master cylinder, it should build up pressure, ok try out this, remove the pipe which is going to the slave cylinder either from the clutch master cylinder or at the clutch slave cylinder and get someone to pump the pedal while you block the pipe and see if there is fluid thrown out with pressure.If there is pressure there thn fit back the pipe and refill the reserviour wth brake fluid and open the bleeding nipple at the slave cylinder let some fluid pour out and tighten it and thn pump the pedal and retry bleeding.
If there is no pressure at the pipe thn its the clutch master cylinder.
Hope this helps!

Dec 14, 2009 | 1997 Acura CL

1 Answer

Fitted new clutch and slave cylinder in 2.5 v6


crawl up under the dashboard & look where the clutch pedal rod goes through the firewall. look for traces of brake fluid at the rubber boot of the rod. a clutch master cylinder normally will leak to the inside of the vehicle & down the firewall when it fails. Replace as required & bleed clutch system using the bleeder valve that should be on the slave asy.

Oct 15, 2009 | 1998 Ford Contour

6 Answers

My 1994 ford rangers clutch pedal just lost all pedal


There are two types of clutch actuators. (Mechanical & Hydtraulic)
A. For mechanical type,- Check the clutch cable as
this could be cut from wear and tear. This is easy
to replace. You can find this connected to the
pedal and the clutch lever near the transmission.
B.For hydraulic operated - Check the level of the
hydraulic oil at the cylinder of the hydraulic
actuator under the hood. This actuator is
directly connected to the pushrod driven by the
pedal. If the actuator is leaking, you have buy
a repair kit (Hyraulic clutch repair kit for Ford
Ranger 1994 MOdel.) These items must be
repaired to activate your pedal.

Oct 14, 2009 | 1994 Ford Ranger Supercab

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

2 Answers

I have no pressure in the clutch and changed the master cylinder


you need to bleed master & slave cyl master dont hold much fluid must bleed similar like brks when when starts coming out of bleeder close bleeder let sit couple of minutes air travel top of master pump pedal more repeat pumping pedal air residue will work it self out

Aug 11, 2009 | 1997 Pontiac Grand Am

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
1998 Dodge Dakota Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...