Question about 1993 Saturn SC2

1 Answer

I have a 93 Sc 2 and cannot keep the drivers side CV joint in the car. Is something bent? If so what is it and how can I fix it? The car is a race car.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

How is it that a race car does not have a mechanic? Seem to go hand in hand. If the car is used for racing, all mechanical parts will wear out rapidly. I would suspect that the control arm is shot, and should be replaced the next time you replace an axle shaft..

Posted on Jul 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

2 Answers

2005 Nissan Altima... replaced drivers side strut and the inner cv joint seperated when the lower arm dropped. The cv joint is still in the transmission but the boot is stretched and the axle will not go...


It can be fixed but now you will need to remove it from the trans and cut the band off the larger side of the boot. then re-alighn the knuckles and slide the 3 joints in 1 at a time. You going to need a new band and the crimper which you can usualy rent from a parts store that has free tool rental. Make sure you grease the joint before you slide the boot back on. Its easier that it looks. When you pull the cv joint out of the transmission some fluid will come out too so use a drain pan. Sometimes they are a pain to get out but a good prybar and some patients usualy works. Pry as you turn the cv joint and it will pop out. Good luck!

Sep 11, 2011 | Nissan Altima Cars & Trucks

1 Answer

I've got a 1999 2500 Chevy Silverado , that I need to change a cv boot on , can u assist me.?


CV-Joints
Overhaul
These vehicles use several different types of joints. Engine size, transaxle
type, whether the joint is an inboard or outboard joint, even which side of the
vehicle is being serviced could make a difference in joint type. Be sure to
properly identify the joint before attempting joint or boot replacement. Look
for identification numbers at the large end of the boots and/or on the end of
the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint
(T.J.) and the Double Offset Joint (D.O.J.).

NOTE: Do not disassemble a Birfield joint. Service with a new joint or
clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should
be checked prior to and after boot service. This is so the boot will not be
installed either too loose or too tight, which could cause early wear and
cracking, allowing the grease to get out and water and dirt in, leading to early
joint failure.

NOTE: The driveshaft joints use special grease; do not add any grease
other than that supplied with the kit.

Double Offset Joint
To Remove:

NOTE: The Double Offset Joint (D.O.J.) is bigger than other joints
and, in these applications, is normally used as an inboard joint.


  1. Remove the halfshaft from the vehicle.
  2. Side cutter pliers can be used to cut the metal retaining bands. Remove the
    boot from the joint outer race.
  3. Locate and remove the large circlip at the base of the joint. Remove the
    outer race (the body of the joint).
  4. Remove the small snap ring and take off the inner race, cage and balls as an
    assembly. Clean the inner race, cage and balls without disassembling.
  5. If the boot is to be reused, wipe the grease from the splines and wrap the
    splines in vinyl tape before sliding the boot from the shaft.
  6. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is
    to be replaced, remove the boot retainer rings and slide the boot down and off
    of the shaft at this time.

To Install:

NOTE: Be sure to tape the shaft splines before installing the boots.
Fill the inside of the boot with the specified grease. Often the grease supplied
in the replacement parts kit is meant to be divided in half, with half being
used to lubricate the joint and half being used inside the boot.


  1. Install the cage onto the halfshaft so the small diameter side of the cage
    is installed first. With a brass drift pin, tap lightly and evenly around the
    inner race to install the race until it comes into contact with the rib of the
    shaft. Apply the specified grease to the inner race and cage and fit them
    together. Insert the balls into the cage.
  2. Install the outer race (the body of the joint) after filling with the
    specified grease. The outer race should be filled with this grease.
  3. Tighten the boot bands securely. Make sure the distance between the boot
    bands is correct.
  4. Install the halfshaft to the vehicle.

Except Double Offset Joint
To Remove:


  1. Disconnect the negative battery cable. Remove the halfshaft.
  2. Use side cutter pliers to remove the metal retaining bands from the boot(s)
    that will be removed. Slide the boot from the T.J. case.
  3. Remove the snap ring and the tripod joint spider assembly from the
    halfshaft. Do not disassemble the spider and use care in handling.
  4. If the boot is be reused, wrap vinyl tape around the spline part of the
    shaft so the boot(s) will not be damaged when removed. Remove the dynamic
    damper, if used, and the boots from the shaft.

To Install:


  1. Double check that the correct replacement parts are being installed. Wrap
    vinyl tape around the splines to protect the boot and install the boots and
    damper, if used, in the correct order.
  2. Install the joint spider assembly to the shaft and install the snap ring.
  3. Fill the inside of the boot with the specified grease. Often the grease
    supplied in the replacement parts kit is meant to be divided in half, with half
    being used to lubricate the joint and half being used inside the boot. Keep
    grease off the rubber part of the dynamic damper (if used).
  4. Secure the boot bands with the halfshaft in a horizontal position. Make sure
    distance between boot bands is correct.
  5. Install the halfshaft to the vehicle and reconnect the negative battery
    cable.






Check the CV-boot for wear
tccs7030.jpg








Removing the outer band from the CV-boot
tccs7031.jpg








Removing the inner band from the CV-boot
tccs7032.jpg








Removing the CV-boot from the joint housing
tccs7033.jpg








Clean the CV-joint housing prior to removing boot
tccs7034.jpg








Removing the CV-joint housing assembly
tccs7035.jpg








Removing the CV-joint
tccs7036.jpg








Inspecting the CV-joint housing
tccs7037.jpg








Removing the CV-joint outer snap ring
tccs7038.jpg








Checking the CV-joint snap ring for wear
tccs7039.jpg








CV-joint snap ring (typical)
tccs7040.jpg








Removing the CV-joint assembly
tccs7041.jpg








Removing the CV-joint inner snap ring
tccs7042.jpg








Installing the CV-joint assembly (typical)
tccs7043.jpg




prev.gif next.gif

Oct 07, 2010 | 2002 Chevrolet Silverado 2500HD

2 Answers

Axle will not come out of the axle housing


I quote from service manual

1 . Raise and support the truck. Remove the rear wheels, the brake drum or brake caliper and rotor. If this is a disc brake, support caliper with wire. Remove seal retainer nuts from axle
housing.

2 . Pull out the axle shaft from housing. Remove the snap ring and bearing race from the axle shaft. Cut the bearing retainer. Break the bearing cage using a hammer and chisel and remove cage and rollers.

3 . Remove the oil seal, the seal retainer and the parking brake assembly (rear). Using a hydraulic press and bearing splitter, press the inner race from axle shaft. Inspect axle shaft for seal wear. Ensure that the shaft is not bent.

2989d8f.jpg

Mar 03, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

My driver side cv joint inner boot keeps breaking


Are you replacing the cv axle yourself. If you are going with an aftermarket axle, that may be your problem. I would recommend going back to O.E. Also, some original saturn parts may be hard to find.

Feb 02, 2010 | 1999 Saturn SL

1 Answer

Cv joint


In addition to the tools needed to remove the tire, break caliper, etc., you will need 2 pry bars and an extrodinary amount of persistance!!!

May 05, 2009 | 1993 Mazda Protege

1 Answer

I have a bent arm going out to the wheel hub is


It's called the CV Joint if that's is the arm you are try to describe. The CV Joint should be connected to the front wheel hub and the other end to the transmission. It may look bent but that's normal unless it's the bar it self. Only the ends should seam like it's bent.
Good luck and hope this helps

Apr 22, 2009 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
1993 Saturn SC2 Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...