Question about 1997 Infiniti.5 J30

2 Answers

Turn signals NOT working

I have turn signals that do NOT work. I have replaced the flasher fuse/checked ALL fuses*(including the ones under the hood) *& I have also checked all bulbs. The switch/button on dash for the 4 way flashers has been damaged *( so I unplugged it) by previous owner when removing dash to take out stereo.
I was told by someone that I should replace this switch as the car needs to make a ''complete connection'' in order for these to work. I don't buy it. Could this be correct? Sounds like alot of malarky' to me. Why would this have to be engaged for them to work?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I have done all of that it's still not working

Posted on Nov 25, 2014

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 297 Answers

You might try replacing the actual flasher unit/relays themselves, just in case. Check all the bulbs, but if that ends up okay, it may be worth a shot to fix that buggared switch. Some manufacturors do run the signals through the flashers, I believe.

Posted on Jul 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 plymouth breeze hazard flasher fuse keeps blowing


check the hazard switch pull the switch and put a volt meter on the connections with wiring connected to switch if it don't respond or just gives you a L.O your switch is bad and shorting out could happen just from being used a lot or something internal broke switch for that shouldn't be all but 50$ or just go to a parts/scrap yard

Jan 22, 2014 | 1998 Plymouth Breeze

1 Answer

My turn signals are not working despite changing the fuse.


the signal flasher may be bad.. its in the box up in the corner.. one for signals.. one for emergency 4 ways..

Jan 08, 2014 | 2004 Toyota Tacoma

1 Answer

Turn signals not working and brake lights not working


replace brake light switch @ BRAKE PEDAL, next, replace turnsignal flasher under dash, check for blown fuse, if turn sig. still doesn't work, check turnsig., switch, & or for loose connection.

Feb 02, 2013 | 1993 Dodge Dynasty

1 Answer

Heater, turn signals and rear wiper do not work


https://s9.postimg.org/4k77afpa7/turn_signal.jpg

Click on the link. I looked at turn signal wiring. Check fuse 15--20 amp under hood fuse box. Not only check the fuse, use a testlight and check fuse circuit for voltage, hot all the time. At the combo flasher, there is also, ignition/run voltage, goes hot with the key on, you can see wire color.
There could be other issues. As you can see, turn signal switch is part of ground circuit.
I could post whole diagram on one link, but, too small to read. Usually with multiple issues, I just pick one and check it out. Fixing one issue may or may not fix the others?

Jun 29, 2017 | 1996 Plymouth Voyager

1 Answer

Turn lights signal is not working


First check the turn signal fuse under the dash if it is good you will need to replace the turn signal flasher which will be near or in the main fuse box or it could be in the high amp fuse box under the hood.

Feb 23, 2011 | 1988 Ford F 150

1 Answer

The turn signals don't work. Which fuse?


it could be one of the fuses in the under the hood fuse boxes, if not check the inside fuse panel and the flasher relay located under the dashboard panel driver side, refer to owners manual/ repair manual for exact location if you have difficulty locating it yourself

Jul 12, 2009 | 1992 Mercury Sable

2 Answers

Where is the turn signal flasher located on a 1995


On the fuse block with the other fuses below the dash

Jul 09, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Turn signal stopped working 1990 Mercury Cougar


I had the same problem and the flasher is not located in the fuse box because it is not a normal flasher. the cougar has an electronic flasher unit that is located on the left side of the center console. the best and cheapest place to order a new one is amazon.com. they run about $30-$40

Jun 07, 2009 | 1990 Mercury Cougar

3 Answers

Blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse


There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

May 29, 2009 | 1998 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...