Question about 2005 Chevrolet Silverado

1 Answer

How do you change the windsheild wiper so I can replace it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Changing the wipe blades is a tough one. Pick the blade up in one hand. In the center of the blade assembly, underneath, there is a button. You'll need a very small screw driver or something small to press the release. push on the release and pull the wiper blade off.

Posted on Jul 17, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my windsheild wipers not work


problably you need to change the braces for the wiper,maybe they are touching in the metal inside and below the winshield,i had the same problem in a toyota tercel and i replace the braces,,,,,,there are a little gasket in the hole to make this adjust and it was broke

Feb 13, 2012 | 1994 Chevrolet K1500

1 Answer

Driver side wiper doesn't work. It moves if you hold it away from windsheild. Did I strip it from frozen snow on windsheild


remove black plastic cap at base of wiper arm,tighten 14mm nut underneath cap while wipers are off and arm is in normally parked position ,replace balck plastic cap and you should be good to go!you might want to snug up the nut on the other one too!

Feb 02, 2011 | 1996 Nissan King Cab

1 Answer

HOW DO YOU ADJUST THE WIPER ARM TENSION HAD WINDSHEILD REPLACE AND NO WIPER IS BLOWING AROUND NOT CLEANING OF WINDSHEILD WHEN DRIVING OVER 45 MPH EVERYTIME A TRUCK GOES BY THE WIPER FLOPS


Hello: From your description of the problem it sounds like the wiper arm is bent. This could have occurred when the windshield was replaced. You might take truck back to who ever replaced windshield and DEMAND they correct the problem. The w/w arm will have to be replaced.

Jan 24, 2011 | 2002 Ford Windstar Cargo

1 Answer

How do I change the windsheild wiper arms?


Hi,
Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage. Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later. Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of work to break it free, but with the right amount of wiggling, it will disengage. Then you can replace the new windsheild wiper arms to it.

Thank you !!

May 26, 2010 | 2001 Chevrolet Blazer

1 Answer

Windsheild Wipers will not move, the arm seems to be slipping on the motor shaft,


It sounds like you live in a climate were snow and ice occurs. If so a lot of people leave their wipers on upon shutting off their cars. If you happen to do that and the windsheild had moister on it or if the snow starter falling while your vehicle was still warm it will freeze. The larger the snow amount the stronger the force will be if you start your vehicle up the next morning with your wipers buried in frozen ice & snow. Since the wipers were not shut off the wiper motor will run and the wiper blades will not. This will strip the linkage the wiper arms press onto leaving you with out working windsheild wipers

Jan 27, 2010 | 2003 Chevrolet Tahoe

1 Answer

Windshild wipers stop intermittingly seems to


your windsheild wiper problem is the wiper module. replace the windsheild wiper module and you'll fix this problem.

Jan 21, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Y windsheild wipers don't move. I hear the


Possible stripped gears or the gears are not making contact.  I would replace the wiper motor.  If you can, and I am not sure, you might be able to replace just the gears.  But given how new the car is, I am sure it comes as an "all in one" unit.  It is possible to seatch www.car-part.com and see if there is a salvage yard around your area that has one cheap.

Mar 03, 2009 | 2006 Pontiac G6

1 Answer

Changing windsheild wipers


Should be a 22 or 24. If you go to Wal-Mart they have a Small Computer in the Isle in Automotive that if you input the Year, Make, and Model into it will tell you Exactly. Quicker than waiting for a For sure Reply here!

Jan 15, 2009 | 2001 Ford Windstar

1 Answer

1991 chrysler lebaron windsheild wipers will not shut off


i think the switch could have got jamed to the on position u may have to replace it to git them to turn off for now there should be a fuse for them pull it

Jan 05, 2009 | 1991 Chrysler LeBaron

Not finding what you are looking for?
2005 Chevrolet Silverado Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...