Question about 2005 Ford F 350 Super Duty

1 Answer

05 f350. trying to remove hub assembly on front left wheel. I am doing the ball joints and axle shaft joint.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 678 Answers

Once you remove the locking hub, the hub and bearing unbolt. There are two different styles of locking hubs. One is held on with a large snap ring that you can pinch with your hands. Once that's out you can pull the locking hub off. The other style bolts on with about 6 or 7 small allen or torx head bolts. Once you remove the bolts the hub pulls out also. They can sometimes get stuck and will require some force.
The axle is also a bit tricky to remove if you've never done it before. You will need two fairly large pry bars and pry between the u-joint ears and the axle tube evenly on both sides to push it out. The axle seal is very tight, also pricey if you damage it, so be careful.

Posted on Jul 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

I am trying to take the lower control arm on the passenger side of a 98 transport. The lower ball joint is being stubborn. I tried ball joint remover tool and not much room to work with and still dont


Lower Control Arm

Print
The lower control arm is a two-piece welded unit with a riveted ball joint. A conventional rubber bushing is used for the rear lower control arm pivot. The front lower control arm bushing is mounted vertically.


REMOVAL AND INSTALLATION

Some special tools are required to perform this operation including, a front hub spindle removal tool and a suitable ball joint separator tool.

WARNING Do not hammer or pry ball joint from knuckle. Failure to use recommended tools may cause damage to the ball joint and seal.
See Figure 1


0900c152801dbd3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Exploded view of the control arm-to-frame mounting

  1. Raise the vehicle and suitably support by the frame allowing the control arms to hang free.
  2. Remove the wheel and tire assembly.
  3. Remove the steering gear outer tie rod from the steering knuckle.
  4. Remove the stabilizer shaft link from the control arm.
  5. Remove the front drive axle shaft nut and washer.
  6. Use a suitable front hub spindle removal tool to Push the axle splines back out of the front wheel drive shaft bearing.
  7. Remove the drive axle from the transaxle.

Drive axle joint seal protectors should be used anytime service is performed on or near the drive axles. Failure to observe this could result in joint or seal failure.
  1. Place a modified inner drive joint seal protector on the drive axle joints.
  2. If equipped, remove the ABS wheel speed sensor jumper harness.
  3. Remove and discard the cotter pin, then loosen the nut from the ball stud.
  4. Remove the pinch bolt and the control arm mounting bolts, then remove the control arm from the vehicle.

Apr 20, 2013 | Pontiac Cars & Trucks

1 Answer

Replace front ball joints on jeep


Hello there,
To replace the front ball joint on your jeep. You will be needing these instruments, Lug wrench Jack, Jack stands, Wheel chocks, Socket set, Wrench set, Needle-nosed pliers, Hub puller, Ball joint separator, Hammer, Ball joint press, Torque wrench, then, Please follow the steps below:
Loosen the lug nuts on your Cherokee's front tires, using the lug wrench. Jack up the front end of the vehicle and brace it with jack stands. Place wheel chocks behind the rear tires to prevent rolling. Back the lugs off the lug nuts, and remove both front tires from your Cherokee.
Remove the bolts behind the calipers. Lift the calipers off the hubs and set them on a support so they do not stretch the rubber lines.
Pull straight out on the brake rotor to remove it from the wheel studs.
Remove the cotter pin from the end of the axle shaft that extends through the hub. This is best done with a pair of needle-nosed pliers. Remove the drive nut from the axle shaft, and set it off to the side.
Remove the three bolts retaining the hub. These 12-point bolts are on the rear of the assembly.
Separate the hub assembly from the knuckle; a hub puller will make this easier.
Remove the cotter pins from the ball joints, using the needle-nosed pliers. You must detach the pins from both the upper and lower ball joints. Use a socket and ratchet to remove the nuts at the bottom of each ball joint.
Insert a ball joint separator between the knuckle and the ball joint. A hammer can be a big help to drive the separator into place and force the knuckle and ball joint apart.
Use a ball joint press to remove the joints. The ball joint press will force the upper and lower ball joints out. Follow the instructions included with your press.
Insert the new joints, using the ball joint press. You must reverse the motion of the press this time, pressing down on the upper joint and up on the lower joint. Be sure that the joints are completely in place within the knuckle.
Reinstall the steering knuckle onto the new ball joints, and thread the nuts onto the bottom of the joint. Check your manufacturer's specifications for the torque requirements for the nuts. Insert the cotter pins, and bend them down around the nut.
Reassemble the hub and axle around the knuckle. When replacing the three bolts, torque them to your manufacturer's specification.
Place the brake assembly back into position, both rotor and caliper. Replace the two bolts you removed on the caliper. Torque the bolts to your manufacturer's specification. Place the wheel back on the Cherokee, and tighten the lug nuts appropriately. With the wheel secured, lower the vehicle back to the ground.
Hope this was helpful to you. Goodluck Elect_Comp

Sep 03, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Need pictures and procedure 91 Ford pickup F250 twin I beam ball joint replacement.


Wheel Spindle, F-150, F-250, F-350
Removal
  1. Raise the front of the vehicle and install safety stands.
  1. Remove the wheel and tire assembly. Refer to Section 04-04 .
  1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
  1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
  1. Remove the rotor from the front wheel spindle (3105).





    Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
    (57-75 Lb-Ft) B - Tighten to 68-92 Nm
    (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)
  1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
  1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
  1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Remove the cotter pin and castellated nut from the lower ball joint stud.
  1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
  1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
    Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
  1. Remove the front wheel spindle and ball joint from the axle.






Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal
  1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
  1. NOTE: Lower ball joint must be removed first.

    Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
  1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
  1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
  2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
    Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.


    Installation
    1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.

      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.

      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
    1. Turn forcing screw clockwise until ball joint is seated.



    2. snorkelbobby_49.gif

Mar 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Need to replace 2003 corola front wheel bearings. need step by step instruction please


Removal & Installation To Remove:
toy_car_cor-02-04wheelhub1.gif

  1. Remove the front wheel.
  2. Remove the front axle hub nut.
  3. Disconnect the front stabilizer link from the strut.
  4. Disconnect the speed sensor (with ABS).
  5. Remove the front brake caliper and rotor.
  6. Disconnect the tie rod end.
  7. Remove mounting bolts and nut and separate the lower control arm from the ball joint.
  8. Using a plastic hammer separate the front axle shaft from the hub.
  9. Remove the 2 mounting bolts from the strut. Remove the knuckle and hub assembly.
  10. Remove the lower ball joint from the knuckle.
  11. Remove the axle hub snap ring from the knuckle. toy_car_cor-02-04wheelhub2.gif

  12. Remove the axle hub from the hub bearing using special tool 09520-00031 or equivalent hub puller.
  13. Remove the inner race from the axle hub using special tool 09950-40011 or equivalent puller.
  14. Remove the dust shield from the knuckle.
  15. Remove the axle hub bearing from the knuckle using special tool 09520-00031 or equivalent and a press.
To Install:
  1. Install the axle hub bearing on the knuckle using special tool 09950-600020 or equivalent and a press.
  2. Install the dust shield on the knuckle with 3 mounting bolts.
    • Tighten 73 in-lb (90 Nm).
  3. Install the axle hub on the knuckle using special tool 09950-600010 or equivalent and a press.
  4. Install the axle hub snap ring.
  5. Install the lower ball joint on the knuckle.
    • Tighten the ball stud castle nut 76 ft-lb (103 Nm).
  6. Install a new cotter pin.
  7. Install the knuckle on the strut with the 2 nuts and bolts.
    • Tighten 162 ft-lb (220 Nm) (except '03-'04) 113 ft-lb (153 Nm) ('03-'04).
  8. Lift the knuckle and hub assembly over the axle shaft and into the hub splines.
  9. Install the lower control arm on the lower ball joint.
  10. Connect the tie rod end to the knuckle.
  11. Connect the stabilizer link to the strut.
  12. Install the front rotor and brake caliper to the knuckle.
    • Tighten the 2 caliper bolts 79 ft-lb (107 Nm).
  13. Install the ABS sensor if equipped.
  14. Install the front axle hub lock nut.
    • Tighten 159 ft-lb (216 Nm) and stake the lock nut.
  15. Check the axle hub backlash and run-out.
  16. Install the front wheel.
  17. Check the front wheel alignment and adjust if necessary.
prev.gif next.gif

Feb 17, 2011 | Toyota Corolla Cars & Trucks

1 Answer

How to remove the right side axel shaft on a 98 olds bravada


1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Feb 13, 2011 | 1998 Oldsmobile Bravada

1 Answer

How do i remove the left cv axle shaft on my 1999 ford escort zx2?


take wheel off take big nut off cv shaft so it can slide out of hub assembly, take bolt out that holds strut to hub assembly an bolt lower ball joint and tie rod end take hammer and tap knuckle where steering end attaches, pry out ball joint and take axle end out of hub assembly. then carefully with pry bar pop it out of tranny. when install cv axle push in tranny fast so that you feel it snap in. good luck

Jan 20, 2011 | 1999 Ford Escort

1 Answer

2000 gmc z71 passenger side cv joint is making noise when i turn......i talk to napa and can get rebuilt for 60$.....but to take it apart....do i need ball joint separator.....what tools..????


Never use a tool myself other than a big hammer. Those forks don't work for me, though we have them. Hit the joint on the side and it will pop out. If not, you can always put the nut back on even with the ball stud and hit it from the bottom. The book also calls for a special tool to get the axle out of the hub. Have never used this either. If it doesn't slide out, I just hit it--I have a new one anyway (take it loose from the tranny before hitting it). Tools you will need are the big socket for the axle nut (around 22mm or so) and regular metric socket set, preferably 1/2 in drive. Also take the speed sensor and brake lines off the support bracket to free up the hub a little more. Note that you may need to also separate the tie rod end if you cannot otherwise swing the hub out far enough to get the shaft out. The book says to take off the stabilizer and shock and also separate the upper ball joint. I don't know if that's necessary or not, as I have not done one on this particular truck. You are doing the whole shaft, right? We don't do individual CVs anymore, as the labor is ridiculous compared to the cost difference to a whole half shaft. Take the axle nut off, unbolt the shaft from the tranny, and swing the hub out. Pull the axle out of the hub first, then the tranny. Reverse procedure to install. I will paste the book solution from autozone.com below. Lemme know if you have more questions.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheel and tire assembly Skid plate, as required. If equipped Drive axle hub nut and washer Brake line and wheel speed sensor support bracket from the upper control arm to allow extra travel of the control arm. Left outer tie rod attaching nut and cotter pin. Separate the tie rod from the steering knuckle
  3. Position the tie rod aside and push steering linkage to the opposite side of the vehicle.

    Lower shock attaching nut and bolt; position the shock aside Left stabilizer bar bracket and bushing at the frame Stabilizer bar bolt, spacer and bushings at the lower control arm
  4. Taking pressure off the upper control arm by placing a support below the lower control arm between the spring seat and the ball joint.
    NOTE Cover the shock mounting bracket and lower ball joint stud with a towel to prevent the axle boot from tearing during removal and installation.


    Upper ball joint cotter pin and loosen (do not remove) the upper ball joint attaching nut. Separate the ball joint stud from the steering knuckle. Remove the attaching nut.
  5. Separate the axle shaft from the hub and rotor using tool J-28733 or equivalent.

    Axle shaft inner flange bolts and shaft
To install:
  1. Lubricate the axle and hub splines with an approved high temperature wheel bearing grease.
  2. Install or connect the following:

    Axle shaft in the hub Inboard CV-joint-to-flange bolts. Torque the bolts to 60 ft. lbs. (80 Nm). Upper ball joint to steering knuckle. Torque the stud nut to 61 ft. lbs. (83 Nm). New cotter pin through the upper ball joint stud and nut, lubricate the ball joint as required. Left stabilizer bar bracket and bushing at the frame Stabilizer bar bolt, spacer and bushings at the lower control arm Lower shock in the mount bracket and the attaching nut and bolt Left tie rod end at the steering knuckle. Torque the nut to 35 ft. lbs. (47 Nm). New cotter pin through the tie rod stud and nut Brake line bracket to the control arm, ensuring the line and/or hose is not twisted or kinked Skid plate, as required Axle hub washer and nut. Insert a drift through the rotor vanes to keep the axle from turning. Toque the hub nut to 180 ft. lbs. (245 Nm) Wheel and tire assembly

Oct 26, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Bad right rear axle. Need to know how to replace axle.


Dana or Ford axle?

Ford here:
SECTION 205-05: Rear Drive Halfshafts 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Halfshaft
Special Tool(s) s2n~us~en~file=st2258a.gif~gen~ref.gif Protector, Differential Seal
205-506 s2n~us~en~file=st2272a.gif~gen~ref.gif Remover, Front Wheel Hub
205-D070 (D93P-1175-B) or equivalent s2n~us~en~file=st2309a.gif~gen~ref.gif Remover, Halfshaft
205-502
Removal and Installation
NOTE: This procedure applies to both rear halfshaft assemblies.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not loosen the rear axle wheel hub retainer until after the wheel and tire assembly are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.
    With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. NOTE: Have an assistant press the brake pedal to keep the axle from rotating.
    Remove and discard the rear axle wheel hub retainer and the washer.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the brake disc.
    1. Remove the two bolts and lift the disc brake caliper and brake pads off the brake disc.
      • Using mechanics wire, position the disc brake caliper out of the way.
    1. Remove the brake disc.
  1. Remove the bolt retaining the parking brake cable bracket to the frame.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Cover the stabilizer link bolt threads and the nut to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a rubber hose approximately 37.5 mm (1.5 in) long, cover the stabilizer link bolt threads and nut.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The bolt that retains the upper ball joint to the knuckle is longer and it has fewer threads than the bolt that retains the toe link to the knuckle. Switching these bolts during installation will prevent the pinch arms on the knuckle from correctly retaining the toe link to the knuckle. This may cause the toe link to separate from the knuckle during vehicle operation. Failure to follow these instructions may result in personal injury.
    Remove the pinch bolts and disconnect the toe link and upper ball joint from the knuckle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the rear suspension upper arm to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a wood stick, approximately 450 mm (18 in) long and 25 mm (1 in) wide, support the rear suspension upper arm.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the outboard CV joint separates from the hub the knuckle will continue to pivot until the brake backing plate presses against the suspension lower arm. To prevent damage to the brake backing plate, immediately after separating the outboard CV joint from the hub, rest the knuckle on a cushioned support that is tall enough to keep the backing plate from pressing against the suspension lower arm.
    Separate the outboard CV joint from the hub and rest the knuckle on a cushioned support.
    1. Using the special tool, press the outboard CV joint until it is loose in the hub.
    1. Remove the special tool.
    1. Separate the outboard CV joint from the hub.
    1. Rest the knuckle on a cushioned support.
04ab306.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the axle shaft oil seal or the machined sealing surface on the inboard CV joint housing.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the splines on inboard CV joint housing to touch the axle shaft oil seal.
    NOTE: A circlip retains the inboard CV joint housing to the differential side gear in the axle.
    Using the special tool, disengage the inboard CV joint housing from the differential side gear.
c231bc2.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the special tool before removing the inboard CV joint housing from the axle.
    Install the special tool.
50c5d1d.gif
  1. Remove the halfshaft assembly from the vehicle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the Differential Seal Protector before positioning the inboard CV joint housing in the axle.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always install the halfshaft with a new retainer circlip and a new rear axle wheel hub retainer.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use power tools to tighten the rear axle wheel hub retainer.
    To install, reverse the removal procedure.

Apr 17, 2009 | Ford Explorer Cars & Trucks

3 Answers

Remove front axle from differential on 2003 dodge ram


That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Jan 06, 2009 | Dodge Ram 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

1,304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...