Question about 1996 Ford Explorer

1 Answer

I have a 2001 Ford F150 XLT with a 4.2L manual trans I am have a problum for the drive cycle to compleate I have a NGS scanner and 3 mo ago i clean the o2 sensor the check engine light has not came on for 3 months i need to take to Arizona emission but the ready status in the evap o2 sensor and catalatic converter will not check to ready compleate status the catallitic coverter and mas airflow sensor and all 4 o2 sensor have been replace in the last year do you know of any TSB or correction download flashes thant will cure this i have followed the ford recomendation proceadure on clearing po1000

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
!@@@

Posted on Sep 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 Ford f150 xlt rear wheel drive. transmission not shifting into 3 shifts from 1 to 2 fine when in overdrive shifts in to 3 feels like neutral. Trans need rebuilt or replaced?


Are there any lights lit on the dash ? check engine , overdrive etc..
could be just a shift solenoid ... Try draining trans fluid an replacing filter. Have to drop transmission pan .. what's the fluid look like ? a nice pink color ? does it smell burnt ? Is it full ?

Feb 25, 2015 | Ford Cars & Trucks

1 Answer

How to remove an actuator on 2001 ford f150 xlt


You need to google 2001 f150 blend door actuator replacement. It is slightly right of center above the plastic duct work for the floor area. All lower dashboard plastic is removed to get at it.
Then the ducting is removed.
http://www.autozone.com/repairguides/Ford-Pick-Ups-Expedition-Navigator-1997-2000/Heating-and-Air-Conditioning/Blend-Door-Actuator/_/P-0900c152801e55ed

Jul 05, 2014 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Fuel engine stops then start up in 1 min


You probably have an electronic ignition system to go with those fuel injectors. It sounds like it runs just long enough to empty the fuel out of the injectors, which means there might be a vacuum problem. I'm a carburetor person myself. Are you sure it sound like it NEEDS gas or could it be flooding?

Mar 29, 2014 | 1991 Ford F150

1 Answer

Ford truck


Do you have 2 gas tanks?

Jun 21, 2017 | Ford F-150 Cars & Trucks

1 Answer

Where is the speed sensor located on a 1994 Ford F150 with a 5 speed manual transmission?


i was told there are 3 sensons on this 1994 ford f150 xlt 5.0 and where are they

Apr 13, 2012 | Ford Cars & Trucks

1 Answer

I need a replacement key and have the vin number my local dealership says 2003. Cant drive my truck what can I do?


If you have a lock smith that can program PATS keys, they might come to your house to cut and program 2 new keys, else you will need to tow it to the dealer.

Without 2 keys or the WDS / NGS tools from Ford ( or the locksmith PATS equipment ) you cannot add a key to drive it, it needs to be programmed.

Dec 30, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I need a fuse diagram for a 2001 Ford F150 XLT


If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Nov 13, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

CD Player Problum


you can try pulling the fuses for the cd then replace them. as the cd is cycling on start up, hold the load and eject buttons, and then hit the unit, in hopes to release the jam.  

Dec 30, 2008 | 2004 Ford Escape

Not finding what you are looking for?
1996 Ford Explorer Logo

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...