Question about 1992 Buick LeSabre

1 Answer

92 buick lesabre, left blinker won't work unless you move it manually. bulbs and fuse are fine. hazards work.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 270 Answers

Hi Friend:

Since you've check or Changed your Bulbs and Fuse also Check or Replace your Turn Signal Flasher,Just as a Percation i would Double Check Fuses,Bulbs and Signal flasher.

If these are All showing bad I would say your Signal Switch has Stopped Working.

To Replace the Signal Swith :

1st Disconnect your Negative Battery Cable.

Remove Steering Wheel (you'll need a Puller, the remove the Shroud around the Steering Wheel Colume.

CAUTION= If you have Air Bags be careful. But you will have to remove the Air Bag Module by removing the coil lock spring Screw.

Then remove the Retaing ring and Coil Spring it will still be attached to your wiring=Just let it Hang.

Next you'll need a Compression Lock Spring Plate Tool.

Attach it to the Center of the Steering Colume, Rotate the Nut Clockwise to Remove,After Compressed you'll see a Metal Snap ring Remove it from the Groove then remove the Tool& Plate

Now you'll need to remove the Plastic Cancel ,the ring and ALL the Bearing including the Bearing Race.

Remove the Signal Arm Lever Screw. then the Signal switch Screws. Pull the Switch out and let it Hang(Still attached to the Wiring.

Get down under then you'll have to look for the screws that hold the wiring to steering colume, Remove then.

Then remove the Retaining Rng and the Wire Plug Protector.Now you Can Pull the Signal Swith Out.

Installing New Swith Simply Reverse the Removal Directions to Install your New Switch.

Please take time to Vote on my Quality of Service and the Help i Provided And a Small Testamony would be Great.If you don't mind.

Thanks for Using FIXYA

From: d_hubbs Good Day Sir





Posted on Jul 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinkers do not work


It may be a fusse. Lights are ok if u replased. But hazards and turning lights have diferent fuses. Check fuse box undes th dahs and hood

Dec 07, 2011 | 1998 Buick LeSabre

1 Answer

My 1998 le sabre blinker (left and right) dose not work but the fuse is good and it worked last night


check your hazard lights if they work then the switch needs to be checked if hazards dont work then replace turn and hazard relay unit under d/s dash

Jan 15, 2011 | 1998 Buick LeSabre

2 Answers

I have turnsignals problem on 92 buick lasabre limited i replaced flasher, all bulbs are good. if i manually move the turnsignal lever up and down the bulbs will flash also hazard lights work what else can...


When you say you replaced "flasher" I'm guessing you mean the combination turn signal flasher unit. If the hazards "flash" on the 4 way but the turn signal does not you are looking at a turn signal switch type problem. ... If 4way flashers do NOT work you need to check wiring immediately around the flasher unit mounting area.Or change Flasher unit Good Luck.

Apr 11, 2010 | 2000 Buick LeSabre

1 Answer

1996 Buick Regal. Blinker Issues


Hello,
I know it sounds strange but I would first check the bulbs and then check the hazard switch. The hazard switch is also the flasher unit. It fails and there are alot of stsange sinarios.

I hope this helps,
Roy

Dec 01, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Right blinker dead left blinker works 2002 buick lesabre limited


RIGHT BLINKER dead ,front,back, or both..???? If front works, and rear doesn"t (REPLACE REAR BULB).....and vice a versa....If rear and front both don't work replace the FLASHER ..Flasher is located in the FUSE block area.......Listen to the operation of the LEFT or RIGHT flasher operation and you should notice a dirrerence....

May 17, 2009 | 2002 Buick LeSabre

2 Answers

Right turn signal not flashing on 1992 Buick LeSabre


I know this will sound Stupid. Get back inside to the Bulb that you Replaced and Turn it Over. Some of these Bulbs will only work if they are in a Certain way. Have that Side Blinker Going when you are Messing with the Bulb to Minimize the Work load on thisPlease Rate my Response, I need all the Help That I can Get! Thanks! Job.

Jan 27, 2009 | 1992 Buick LeSabre

2 Answers

The blinkers quit working


Do u mean the hazard flashers work, but not the turn signals? If so, check the turn signal flasher, it should be replaced. If I didn't understand your question, let me know.

Dec 14, 2008 | 1993 Buick Regal

Not finding what you are looking for?
1992 Buick LeSabre Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...