Question about 2004 Infiniti QX4

Open Question

Rear wheel seal replacement on infinity qx4

Rear wheel seal replacement on 2000 infinity qx4 on passenger side.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: tryen to find location of the crank sensor on 1998 infiniti QX4

looking for crankshaft sensor on 1998 infiniti qx4

Posted on Nov 17, 2010

Puterwiz82
  • 60 Answers

SOURCE: 2002 Kia Rio rear wheel bearing passenger side

I'm from the United States, East coast.

Posted on Nov 24, 2008

bibleman01
  • 334 Answers

SOURCE: 2001 Infiniti QX4 low beam bulb replacement instructions

Look directly behind the headlight box if there is a rubber sleave covering the plug take it off. Unplug the wires from the bulb, there may be a saftey clip you will have to pry up to get it off.after you get the plug off the bulb holder should twist counterclockwise then it will pull right off.When you change the bulb just remember to wipe your body oil off the bulb before attaching it back into the headlight box. Then plug it back in and your in business. The high beam has three wires and the low beam has two wires. The bulb will have to be the right one.
God Bless You Greg

Posted on Nov 25, 2008

  • 400 Answers

SOURCE: how to change my front differential seal and

That will be a Huge job. The whole front diff must come out of the car and the case will need to be taken apart to even gain acess to the carrier side bearings.
The hub bearing is where the wheel bolts up is that maybe what you are talking about?
Also the axle seal isn't that bad to do you need to remove the cv shaft then it's just a simple remove the seal and install the new one.
But all of these jobs will be big ones.

Posted on Oct 13, 2009

  • 86 Answers

SOURCE: 2003 Infiniti G35 - VDC, slip and brake lights on

The abs sensor may have been damaged when the repair was done.

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 83 Bronco 351w I am doing the brakes and the passenger side rotor needs to be replaced can someone walk me through this thanks


Personally I would replace both rotors to prevent a future brake imbalance.

* chock rear wheels, raise front of vehicle and place on stands.

* remove wheels, remove brake calliper and bracket assemblies.

* remove bearing hubs from axles, via removal of bearing adjustment nut

*remove hub seals, clean and inspect bearings, repack with HT bearing grease.

* the brake rotor bolts to the rear of the hub, you will have to remove and replace rotor to hubs, make sure all bolts are thread locked with loctite 263 and tensioned to spec.

* pack hub with grease, install seals, fitt hub assembly and adjust wheel bearing preload, install new split pins.

* fitt brake calliper and brackets, fit new brake pads,

* fitt wheels lower vehicle, test brake for function

Hope this helps..

Aug 02, 2016 | Cars & Trucks

1 Answer

My 95 blazer feels like something is not releasing or something is "dragging" in rear end


The greasy one has a seal leaking between the backing plate and the brakes (axle seal) which in turn will cause your brakes to grab on that wheel when you apply the brakes. Remove the axle and replace the seal. Then thoroughly clean the brake shoes and backing plate until they appear bone-dry like the other side. This should solve your problem. Make sure the rear-end grease level is full when you finish.

Mar 18, 2014 | 1995 Chevrolet Blazer

1 Answer

Rear brake on passenger side getting wheel hot, GMC Sonoma


I have a 2003 gmc Sonoma ZR5 4x4 the wheel bearing went out on the passenger side I replaced both bearings when I got it back together the brum on that side was getting hit I replacer the caliper on both sides an its still getting hot only on that side what could it be

Sep 03, 2012 | Oldsmobile Cars & Trucks

1 Answer

Screeching noise from passenger side on the rear


might be the alternater belt needs to be tighten

May 21, 2012 | 2004 Infiniti G35 Sport Coupe

1 Answer

I'm trying to find out how to replace the front passengers side wheel bearing.


Unfortunately, more information is required to provide the correct solution. Some vehicles have sealed wheel bearings and some have fully serviceable setups. Front and rear wheel drive will make a difference too. What kind of vehicle are you working on? And a brief description of why you need to replace them would also help.

Aug 12, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

Pssngr window Infiniti G37 Coupe not raising after dr is closed


sound like you have a broken wire to wind motor that making intermintant contact ck where wires come into door assm

Nov 25, 2009 | Infiniti G37 Cars & Trucks

1 Answer

Just replaced hub on passenger side only 80k is this normal also have rear axle seal leaking do i have to remove pumpkin cover to pull axle or will it come out with just removing outer bolts


yes this is normal wear, if you have aftermaket wheels and tires the wear will be quicker do to more stress on the bearing, for the rear seal no u do not have to remove the cover if you jack up the side that has the bad seal you dont even have to drain the fluid. the outer bolts hold the axle in. there is no c clip inside the axle to remove

Sep 27, 2009 | 2005 GMC Sierra 2500HD 4WD

1 Answer

Infinity G35 Tires


You cannot rotate front to rear because you have 17in 225 50's on the front and 235's on the rear. The rear tires (and wheels) are slightly wider than those on the front. You can get all the same size...225's if you replace the rear wheels. When you see the price of those wheels, you'll probably continue to purchase tires. You could get a tire with better treadwear..(harder compound), however you will sacrifice ride and handling and probably noise. I would not recommend side to side rotation because unless the tires are remounted and rebalanced, you will change direction..not recommended on radials.

Jun 20, 2009 | 2004 Infiniti G35 Sport Coupe

1 Answer

Rear Brakes


If you have any flex/rubber lines at or near that rear wheel, I'd change it.

Oct 13, 2008 | 1997 Dodge Intrepid

2 Answers

2002 infiniti q45 has abs light and traction light on?


I have the ABS/SLIP/TCS OFF light problem and solved it by replacing the ABS integrated relay module. It sits above the ABS actuator which is located just in front of the passenger side of the firewall and it has 3 connectors exiting the module and one attaching screw at the top.

I have no idea what might be causing your other issues.

Aug 01, 2008 | 2004 Infiniti Q45

Not finding what you are looking for?
2004 Infiniti QX4 Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14223 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...