Question about 2000 Chrysler Sebring

1 Answer

How do i remove the driver's inside panel door? My electric button panel for windows and locks isn't moving.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 17,970 Answers

Like reference guide, check this procedure to Removal & Installation / Door Lock Motor...

The door lock motor is integral with the door latch. If the door lock motor is found to be defective, the entire door latch must be replaced.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Roll the door glass down.
  3. Disengage the 2 clips attaching the speaker grille to the door trim panel. (They are at the front of the grille, one near the top, and the other one at the bottom).
  4. Remove the 3 large washer-headed screws surrounding the speaker.

    How do i remove the driver's inside panel door? My - 6acb803.jpg
    Fig. Fastener location for the door lower trim panel
  5. Remove the access cover at the front of the door trim panel. Remove by prying at its rear edge.
  6. Remove the red courtesy reflector from the lower tail of door. Disengage by prying at the screwdriver notch at the bottom of the reflector.
  7. Remove the flag trim panel from the door by prying it off at the 2 attachment clip points.
  8. Remove the 7 screws attaching the door trim panel to door:
    1. One screw is located at the lower rear screw pocket.
    2. Three screws are located along the bottom of the door.
    3. One screw is located inside the handle opening.
    4. One screw is located at the upper front.
    5. One screw is in the pull cup.
  9. Disengage the 2 hidden clips attaching the rear of the trim panel; pry them off at the 2 attachment clip points.
  10. Lift the trim panel upward and away from the door, disengage the trim panel from the upper retainer channel.
  11. Disengage the clip attaching the latch linkage to back door handle.
  12. Disconnect the electrical connectors as necessary, including the lower foot light, if equipped.
  13. Remove the door trim panel from the door.
  14. Remove the water shield (water dam) from the inside of the door.

    b5ff0ae.jpg
    Fig. Remove the flag trim panel, door trim access cover, inside remote handle, and power door lock switch
  15. Raise the door glass.
  16. Remove the bolt and nut for the rear glass run channel and position the channel aside.
  17. Disconnect the lock rod from the lock button bellcrank.
  18. Disengage the lock and latch rods from the clips on the inner door panel.
  19. Disconnect the lock and latch rods from the outside door handle and the key cylinder at the door latch.
  20. Disconnect the wire connector from the power door lock motor.
  21. Remove the screws attaching the door latch to the door end frame.
  22. Remove the door latch and the power door lock motor from the vehicle.

    c5c04cf.jpg
    Fig. Expanded view of the door lock, latch, and linkage


    185c44d.jpg
    Fig. View of the door lock button, latch rod, lock rod, and door latch

Hope helps (remember rated this).

Posted on Jul 05, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BeninVa
  • 389 Answers

SOURCE: How do I remove inside door panel with electric

Hello, I can help you with this.
Look toward the front bottom and remove that screw, then there is one at the armrest. With power windows, use a small screwdriver and carefully pry up on the switch assembly and unplug the connectors. remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.

Posted on Apr 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The rear passenger door locks do not work on our 1999 GMC Suburban. I've checked the fuses and they all work; I tried to physically pull the lock button but it will not move: and I attempted to open the...


If the lock button doesnt move look like you door lock actuator jam you have to find a way to move the rear panel by the inside and unlock it manualy

Mar 22, 2015 | 1999 GMC Suburban

1 Answer

Tailgate won't open


is this a RKE FOB only statement, and no keys tried?
all buttons tried? in car and the fob button?
Usually there are 3 ways, at least. Fob, real key and door switches.
the driver on some cars have a button to open all locks in car.


all ways, tired, inside and outside.?
id remove the inside tail gate, panel.
the lever to the lock is there. move the lock by hand iniside, i bet it opens now.


on most cars there is a child lock feature, its covered in the operators guide the fact there. read that. first.

wits end.?
id remove the inside tail gate, panel.
the lever to the lock is there. move the lock by hand inside, i bet it opens now.

Mar 13, 2014 | 2008 Jeep Grand Cherokee

1 Answer

Driver side door will not unlock manually or electric. can feel actuator rod to lock moving but not enough to unlock. Have tried working the lever manually no good. Help


Put the window down & look inside the door
with a small light & hook the necessary linkage
to unlock the door

Then remove the inner door panel & make the repairs

Jun 29, 2011 | 1994 Buick LeSabre

1 Answer

Electrical mechanism will not unlock front passenger door nor can it be unlocked manually at door handle. Inside door handle will not move so door cannot be opened. Consequently, cannot remove inner door...


possibly your linkage from the electric solenoid and door lock to the locking mechanism has either fallen apart inside the door or also possibly it has gotten "over-center" and cannot operate properly from either the automatic electric or manually from the key, can you hear and click from the solenoid when you operate this electrically? and see lock button move a little,this would be a sign it's over-center.

Sep 24, 2009 | Toyota Sienna Cars & Trucks

1 Answer

I have a 1993 Ford Tempo and am having problems removing the motor from the door. I already have the door panel removed and the power disconnected from the motor.


remove the door panel and check to make sure the linkage to the lock assembly is still attached. I can't give an estimate because I don't know what is wrong at this point

are the locks manual or electric?i have seen most electric locks freeze up because of rust/.corrosion.the rubber accordian seal fails and moisture does it's job.there is no lubrication on the mechanism.it's basically a push pull magnet tube with a spiral grooved actuator rod.this is to assure no accidental vibration/jar induced movement.also means very difficult to budge when corroded.i have gotten a few to move by grabbing lock post with pliers and pulling hard.good luck!



Rear Door Window Regulator and Motor
Removal and Installation
Remove the rear door trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
Remove the door mounted speaker.
Remove the watershield.
NOTE:The glass must be lowered for this step.

NOTE:Some vehicles may use rivets to attach the glass to the regulator.

Remove the bolt that attaches the glass to the regulator.
Raise and support the rear door window glass to the full up position.

NOTE:Do not detach the door handle from the latch cable during this step.

Remove the rear inside door handle.
Remove the screw.
Disengage the inside door handle from the door.
If equipped, disconnect the power door lock rod from the back of the inside door handle.

Gain access to the power window motor electrical connector located in the front of the door.
Fig. 90: Identifying Power Window Motor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the power window motor electrical connector.
Press down on the connector tab.
Pull the connector upward and remove through the speaker opening in the door.
Disconnect the rear door window regulator and motor assembly from the door.
Remove the nuts.
Remove the screws.
Fig. 92: Disconnecting Rear Door Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_2.jpg
Remove the window regulator and motor assembly from the door.
Fig. 93: Removing Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_3.jpg

To install, reverse the removal procedure.

Jul 01, 2009 | Ford Tempo Cars & Trucks

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

How do I remove the inside door panel on drivers side


you need to take out the door panal and work from the inside of the panal. Open it from there.

Jan 11, 2009 | 2001 Mercury Grand Marquis

1 Answer

95 blazer, front driver window motor broken need to get window up


When removing the door panel, you need to remove all of the screws first. Then pull the door panel off. There should be screws around the edges or the door panel, and 1-2 screw on the door handle(on the inside). Then pop the door panel off, if the blazer has electric windows and locks you have to disconect them first, if it doesnt have power locks and windows, you have to take the window crank off,there should be a screw in the center of that. Unscrew the door lock and pull up. If it doesnt have them locks then you have to disconect it from inside the door panel

Nov 30, 2008 | 1995 Chevrolet Blazer

1 Answer

Ford Escort 1998 central locking


Are you talking about the key cylinder or the electric lock button? If you are talking about the key,you need to remove the door panel and watch the lock rod move up and down. There is a plastic clip that pops open or breaks from age. If you are talking about the electric lock, will the passenger door lock move when you press the lock button on the drivers door? Does the passenger door make a grunt noise when trying to lock/unlock?

Aug 25, 2008 | 1998 Ford Escort

Not finding what you are looking for?
2000 Chrysler Sebring Logo

1,964 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...