Question about 1997 GMC Sierra

Open Question

How to install a gm relay 12135196/dual battery upgrade?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 park ave cooling fans dont run


Watch this video , shows how to diagnose GM cooling fans , controlled by three relays ! Relay Driven Dual Cooling Fan Diagnostics

Jun 04, 2017 | Cars & Trucks

1 Answer

Turn signal relay by left foot needs replaced. I can't figure out why it won't pull out of the convenience center. Is there a retaining device I'm missing?


GM Turn Signal Problem Fix - Directional Relay Replacement

? 5:38
www.youtube.com/watch?v=y4QVUBVVVpI
May 3, 2014 - Uploaded by Steve O
GM Turn Signal Problem Fix - Directional Relay Replacement ....You will need to install resistors in series with the directional LEDs

Sep 22, 2015 | Cars & Trucks

2 Answers

Starter wont turn


Check the battery charge. Do you hear a click if the battery is good? Maybe Starter solenoid is bad. If the battery is good, and no click. the wire to the Starter solenoid is a bad connection, or wire broken, or trace that wire back to a relay, and from relay to ignition switch terminal may also be bad. A jumper around certain wiring may help isolate the problem.

Apr 01, 2015 | 2001 Saturn L-Series

1 Answer

Bought a used 1983 southwinds motorhome but no batteries. does someone have a wiring diagram for the batteries


no diagrams but the reason for duel 6 volt batteries is for proper distribution of power you can put duel 12 volt in it and it will seem to run fine but over time fueses will get weak and start to pop as well as relays. i hope this information helps. J&D services

Sep 22, 2012 | 1983 Chevrolet Suburban

1 Answer

1997 chevy cavalier. Is there any way to bypass the ignition switch? The car will turn over with a screwdriver to the starter.


The problem is most likely the starter relay, not the ignition switch. Ignition switches had a high nfailure rate in Cavaliers due to starter current. GM issued a recall and added a starter relay to solve this. The relay will fail periodically, resulting in a much easier and cheaper fix than a new ignition switch. If your Cavalier has the relay, you will find it in the very front of the engine compartment, just left of the battery, fastened to the back side of the radiator crossmember. GM Dealers have the relay for about $30.00.

Aug 09, 2011 | 1997 Chevrolet Cavalier

1 Answer

I have a fisher plow every time i move ther plow control up or side to side the vehicle stalls


If your plow is electric/hydraulic then you will have to introduce a second battery into the system and upgrade your alternator to a heavier one. The good news is that GM has the battery kit, it can be found in any diesel truck in a salvage yard or ordered from the dealer. Upgrade your alternator to at least a 70 amp output. If you have a local battery and electric shop they can upgrade your current alternator for a lot less than buying a new or rebuilt one. Hope this helps.

Dec 07, 2010 | 1996 GMC Sierra

1 Answer

How and What additional parts are needed to install a second battery into a chevrolet Silverado 2500 HD pick truck?


You need a second battery box and some cables. This is a package you can get at the dealer. The older diesels all came from the factory with a dual battery setup. You could also probably find it at a junk yard. Just check under the hood on any diesel GM truck there. Hope this helps.

Aug 29, 2010 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

Need to find heater blower resistor on 1991 Buick Park Avenue


GM: Electra/Park Avenue/Ninety-Eight 1990-1993 REpair Guide
Blower Resistor Module


b4bdc8d.jpg

Fig. 1 Blower resistor assembly is underneath the fuse block
REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Remove the rear sight shield.
  3. Remove the fuse/relay block assembly and bracket.
  4. Disconnect the resistor module connector.
  5. Remove the retaining screws and remove the resistor module.

To install:
  1. Inspect the gasket and replace or repair as required.
  2. Install the resistor module and secure with screws.
  3. Connect the resistor module connector.
  4. Install the bracket and fuse/relay block assembly. Install the sight shield.
  5. Connect the negative battery cable, and check the climate control system for proper operation.
Hope this help (remember rated and comment this).

Mar 29, 2010 | 1991 Buick Park Avenue

1 Answer

2000 Blazer 4.3 no fuel


Did the new pump come with an upgraded wiring harness? GM had problems with the connector that plugs into the pump assembly on top of the tank. The better brands of pumps come with this upgraded wiring. You might want to check into that.

Feb 19, 2010 | 2000 Chevrolet Blazer

3 Answers

How do you put a starter solenoid in a 1988 ford f150?


Ford does not put the solenoid on the starter itself, so then it is just a relay, usually on a fender. It will have 4 wires. Two thick ones from the battery and to the starter. And 2 thin ones from ignition switch and to ground.

Oct 31, 2009 | 1988 Ford F 150

Not finding what you are looking for?
1997 GMC Sierra Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...