Question about 1999 Pontiac Bonneville

1 Answer

Bolt size for a 1996 bonneville torque converter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

Usually the bolt size is a 1/2 inch or 13 mm if not then its a 10mm

Posted on Jul 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 ford explorer Manual trans. 2 door 6 cyl. 2 wheel drive repair diagrams


As per what you requested Transmission to engine bolts: 35 lb-ft (E/MWM).

But if you need more torque specs for other parts of your vehicle.I suggest you to check the link below with complete torque specification list and helpful diagrams.
http://www.allcarhelp.com/2016/05/torque-specs-for-bolt-size-of-bolts.html
This will help.
Thanks.

May 08, 2016 | 1996 Ford Explorer

1 Answer

I need torque sequence for rod bearing caps


There is no sequence for the rod caps Since there are only 2 bolts per cap you only have to snug up each bolt then apply half the listed torque value to each cap bolt. then continue back and forth on them until the end torque value is applied to both bolts.

Apr 29, 2015 | 1996 Pontiac Bonneville SE CA Value

1 Answer

Isuzu rodeo 1996 3.2L V6. Torque specs for alternator pivot bolt 14 mm and lock bolt 12mm. torque for AC idler pulley lok nut 23 mm


Isuzu does not list specific torque values for these fasteners. When this is the case, you are expected to use standard torque values. These can be found on the chart I have linked below. Be advised that bolt sizes go by the diameter of the shaft [round shaft portion] of the bolt or stud, NOT the hex head [socket size] of the bolt or nut. Partially remove the bolts so that you can measure the shaft and obtain the correct torque from the chart. See


https://www.swtc.edu/ag_power/diesel_engines/lecture/metric%20torque%20values.pdf

Sep 26, 2014 | 1996 Isuzu Rodeo

2 Answers

How many ft/lbs of torque is recommended on the flywheel bolts when installing the flywheel on a 1996 GMC Sierra Z-71 4x4 5.7L engine?


GMC Sierra Bolt Torque Specifications. ... The torque converter bolts to the flywheel with 46 foot-lbs. of torque. ... 1996 GMC Sierra Horsepower Torque Specs.

May 02, 2014 | Cars & Trucks

1 Answer

Missing bolts on '73 superbeetle...


I wouldn't get them from the bolt store. Usually torque converter bolts have a special head on them. I would find a vintage beetle specialist online and get them from them. You could also buy an assortment of bolts to get the correct thread count and size found and then order torque converter bolts from a parts store. Oreilly's has some of the more standard converter bolts...

Nov 11, 2009 | Volkswagen Beetle Cars & Trucks

1 Answer

Trying to put a transmission into 1996 town and country van get transmission bolted into place and motor and transmission will not turn over something bound up could it be the torque converter or is it...


Must install converter into tranny first. Then bolt torque converter to flywheel after you slide it into place. Make sure converter slips into tranny..you will need to turn it several times untill it fits into grrove inside tranny.:)

Sep 07, 2009 | 1996 Chrysler Town & Country

1 Answer

Auto transmission removal


remove the transmission. the torque converter should just stay on the motor. if its bolted the engine the bolts will now be uncovered. if its a slip on mark the converter and the shaft to make sure you line in back up right.

Sep 24, 2008 | 1996 Toyota Land Cruiser

Not finding what you are looking for?
1999 Pontiac Bonneville Logo

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...