Timing marks for 2001 vw passat 2.5l - 2002 Volkswagen Eurovan

SOURCE: throttle body in 2001 Passat

throttle body is located at intake manifold ..follow snorkle from air cleaner to where it attaches to motor ..looses hose and clean with carb cleaner there..open blades(throttle) to get behind entry good also..... fuel filter is located in tank and in line from fuel tank just in front of tank inline with fuel line...good luck

SOURCE: need 2001 vw passat 4cyl. 1.8t. timing belt diagram

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

SOURCE: How do i retract rear caliper piston on 2001 vw passat?

the piston needs to be screwed back in as it is being compressed. there are several aftermarket tool you can buy to do this from 10 to 200 dollars depending on how nice of a tool you want.also make sure when compressing piston that the hand brake is off all the way.

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

SOURCE: I am having troubles locating

hi, here is a guide i have come across on this site written by another expert it should be the one for your engine but always double check.

If you are unsure what you are doing then please go out and buy a haines workshop manual as these tell you every detail you need to know so that would be your best solution.

Please dont do this work if your unsure what you are doing as you could damage the engine beyond repair so you have been warned;

it covers single cam and if you scroll down it shows double cam ok

Sep 14, 2009 - VW Passat & Audi A4 1990-2000 Repair Guide
Timing Belt - REMOVAL & INSTALLATION

2.8L SOHC (AFC) V6 Engine

1. Note the radio security code and disconnect the negative battery cable.
2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.

1. Remove the Crankshaft Position (CKP) sensor from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
4. Loosen the tensioner roller and remove the drive belt.

1. Install the timing belt over the sprockets, then the idler rollers and lastly over the tensioner.
2. Install camshaft alignment tool holder Tool No. 3243 into the camshaft alignment flanges.
3. Check and adjust the cam belt tension such that the upper left portion of the belt between the tensioner and the left cam gear can just be twisted 90° ( 1 / 4 turn).
4. Tighten the cam belt tensioning roller to 33 ft. lbs. (45 Nm), and the camshaft sprocket bolts.
5. The balance of the installation is in reverse order of removal.

1. Note the radio security code and disconnect the negative battery cable.
2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.

1. On the cylinder block near the crankshaft, remove the sealing plug from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
4. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, insert a 2mm spring pin through the tensioner housing and tensioner plunger to secure it in place. When the plunger is secure, release the wrench tension.
5. Remove the damper-to-crankshaft bolts and the damper.

1. Remove the serpentine belt idler and the crankshaft damper guard.
2. Mark the running direction of the timing belt and remove it from the pulleys.

Fig. Crankshaft pulley alignment location for TDC-Audi 2.8L V6 engines

Fig. Left camshaft sprocket alignment position for TDC; right camshaft position is similar-Audi 2.8L V6 engines

Fig. View of crankshaft holding tool installed-Audi 2.8L V6 engines

1. Make sure that the camshaft pulleys and the crankshaft pulley are in alignment with TDC of the No. 1 cylinder's compression stroke.
2. Install the timing belt; make sure the timing belt is installed in the correct running direction from which it was removed.
3. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, remove the 2mm spring pin from the tensioner housing. Slowly, release the tensioner spring pressure to put pressure on the timing belt.
4. Install the crankshaft damper guard and the serpentine belt idler pulley; torque the idler pulley bolts to 33 ft. lbs. (45 Nm).
5. Install the crankshaft damper and torque the damper-to-crankshaft bolts to 15 ft. lbs. If the damper-to-crankshaft center bolt was removed, torque it to 147 ft. lbs. (200 Nm) plus 180° 1 / 2 turn).
6. Remove the Crankshaft Holder tool No. 3242 and install the sealing plug.
7. Replace the remaining components by reversing the removal procedures.
8. Refill the cooling system and the automatic transaxle. Connect the electrical connectors. Install the negative battery cable last.
9. Test drive the vehicle.