Question about 2002 Jaguar X-Type

1 Answer

Air con automaticaly turn on when you switch the blow postion to the windscreen position.

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Its supposed to come on when you select that position because actually thats the defrost for the windsheild so iit shoots out high select medium for it to blow through vents

Posted on Jul 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know why I'm getting heat through front dash vents then when I switch to defrost it blows really cold air 2006 equinox


In the defrost position, most cars will automatically turn on the a/c so that the windscreen will be cleared.

Jun 21, 2016 | Cars & Trucks

1 Answer

Heat does not blow onto windscreen but blows through other vents - whats wrong


What make an model an year vehicle do you have ? The air blows out of the floor vents an center vents but not defrost ? Possible mode actuator , stuck mode door ! There is a door inside the heater / A/C assembly that directs the air to the desired position . These doors can be moved by a vacuum operated actuator or an electric motor . Sometimes thing's put on the dash end up inside the heater box , fall through defroster vent ! Pens , pencils etc.. Depends on the make vehicle an system , manual , or automatic climate control . Some of the newer vehicles the HVAC system as it is called , the control panel is a electronic control module an can store DTC'S - diagnostic trouble codes !

May 07, 2015 | Cars & Trucks

1 Answer

How to relearn throttle body on a Lexus is250


Pedal Relearn Procedure
Accerlerator Pedal Released Postion Learning is and operation to learnicon1.png the full released postions of the accerlerator pedal by monitoring the accelerator pedal sensor output signal. It must be performed each time harness connector of accelearator pedal postion sensor or ECM is disconnected.

1. Make Sure the acceleartor Pedal is fully released
2. Turn Ignition switchON and wait at least 2 Seconds.
3. Turn ignition switchOFF and wait at least 10 Seconds
4. Turn Ignition switchON and wait at least 2 seconds.
5. Turn Ignition switchoff and wait at least 10 seconds

Throttle Valve Relearn
Throttle ValveClosed Postion Learningicon1.png is to learn the fully closed postion of the throttle valveby monitoring the throttle position sensor output signal. It must be performed each time harness of
electric throttle control actuator or ECM is disconnect.

1.Make sure accelerator pedal is fully released.
2. Turn ignition ON
3. Turn igntion switch OFF and wait at least 10 seconds. Make sure that the throttle valvemoves during the 10 seconds by confrming the operating sound.
(You can hear the TB sound when you have key on and shifter in first gear and step on the gas. So you know what you listening for.)


Idle Air Volume Relearn Procedure
The Following Condtions Must be met in order for procedure to Work.

Battery Voltage :More than 12.9 volts at idle
Engine Coolant Temp 158-203 degrees Farenhiet
Electric Load Switch OFF i.e Air Condition, headlamps , rear defogger
Steering Wheel: Neutral Postion (Straight Ahead)
PNP Switch: OFF (Park Neutral Switch i.e. Clutch Switch...pretty sure)


1. Perform ACCERLEARATOR PEDAL RELEASED POSTIONS LEARNING
2. Perform THROTTLE VALVECLOSED POSITION LEARNING
3. Start engine and warm it up to operation temperature
4. Turn igniton switch OFF and wait at least 10 seconds
5. Confirm Gas Pedalif fully realeased, then turn igniton switch ON and wait 3 seconds
6. Fully step on and release gas pedal5 time within 5 seconds
8. Wait 7 seconds and fully step on gas and stay on until MIL stops blinking and is steady.
9. Fully release the Gas pedalwithin 3 seconds after the MIL has turned ON steady.
10. Start engine imediatly and let idle. Wait 20 seconds.

Sep 22, 2014 | Lexus IS 250 Cars & Trucks

1 Answer

My car heater recently stopped working. It just blows out cold air! Before it stopped working the cold and hot switch wasn't turning so i forced the knob to turn and since than my heater hasn't worked....


Check the heater tap under the bonnet or is usually located close to fire wall near the windscreen just follow the pipes that come out one set will go to the air con the other set will connect to the tap and then radiator

Jun 17, 2017 | 2001 Hyundai Sonata

1 Answer

Winndscreen does not clear unless have air conditioner on


Blowing air across the windscreen does not necessarily clear away condensate from the inside. Water vapor condenses on any cool surface, and humid air blowing across a cool windscreen will result in more condensate on the windscreen. Often the air that blows across the windscreen is just humid AND heated, and doesn't solve the problem.
The air conditioner system performs two functions. Not only does it cool the air, it also extracts moisture, resulting in dryer air. Once the dried air is re-heated in the defroster system, it should allow the moisture on the windscreen to evaporate.
In other words, it sounds as though the defroster system is functioning properly.

Feb 06, 2011 | 1998 Volvo S70

1 Answer

Air con just blows hot air s type jag


With the key in the off position; remove the RDO BAT fuse for at least 10 seconds then replace the fuse; turn on or start the vehicle and try the A/C again. Removing the fuse should reset blend actuators

Apr 15, 2009 | 2005 Jaguar S-Type

Not finding what you are looking for?
2002 Jaguar X-Type Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...