Question about 2003 GMC Yukon Denali

1 Answer

I recently purchased this truck at a dealer and didnt notice the front bumper was higher on the left side. After inspecting it I see that the right side is conected with the three screws and the left side is missing these and is connected on the bottum by a single screw. How can I fix this?

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 502 Answers

Put more screws in,or,take it back to the dealer

Posted on Jul 04, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Right front tire rubbing on bumper when turning left

  • Possibly body damage
  • Left and right tire sizes could be different

Nov 14, 2017 | Cars & Trucks

1 Answer

How do you take off front bumper on new dodge dart

Take out all the clips on the top of the bumper in the eninge compartment, the there are four bolts in each fender well, then eight bolts on the bottom of the bumper. Slightly pull on the side of the bumper and it'll come right off, I just recently had to do this for the same reason.

Dec 29, 2012 | Cars & Trucks

2 Answers

I got a NM pajero, recently a vibration started when driving around 60kmph. It appears to be comming from front left side.At higher speed it goes away.Could any one give me a clue.Thanks

more then likely could be an off balanced tire or a tierod end do a complete inspection of all your joints and look for bad spots in tires... even new tires can have bad knots in the bands

Nov 18, 2010 | 2002 Mitsubishi Montero

1 Answer

Front bumper replacement diagram

Not familiar with Hondas, but to remove the bumpers on cars I've worked on, there are usually 8 bolts, 4 that attatch the bumper to the right side frame, and 4 that attatch to the left side. Be careful, that you remove any screws that attatch to the side panels FIRST!

Apr 12, 2010 | 1998 Honda Civic

1 Answer

How do you take bumper off a ford puma?

Front Bumper (434230)

1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

1. To install, reverse the removal procedure.

Jan 01, 2010 | 2007 Ford F

1 Answer

Front bumper cover is broken, no lights along bottom.

Under the bumper cover is a fiberglass bumper. It could be broken or your bumper mounts could be bent on that side. It is best to remove the screws (on the side of the wheel well) and 10mm bolts holding the bumper cover, and locate the two frontal bolts in each bracket. There are also some plastic push pin nuts in various spots too. Don't try to get the push pins under the headlights, they will come with when the bumper is removed.

Sep 25, 2009 | 1993 Honda Accord

1 Answer

2003 golf tdi oil problem

If you have recently had work done on the vehicle, and it was oil related, i would take it to the car wash and clean the underside of it really good, this way you can trace where the oil is coming from, that way you can pinpoint the drips.

May 05, 2009 | 2003 Volkswagen Golf

1 Answer

Change headlight

1) Left side is in front of the Airbox for the aircleaner. 2) Right side is in front of the battery (which HAS to be removed to replace the bulb).
3) Replacing the BULBS for $10 each is all you normally need to do - Unless the lights are Fogging and getting Condensation in them.
The you have to remove the bumper to repace the headlight assemblies. It is a pain. Costs $300-600 at a dealer.

Dec 26, 2008 | 1999 Jeep Cherokee

1 Answer

Front driver side bumper damaged

What sort of damage is it? What solution are you looking for? I recently did the same thing to my 95.
I'm about to go out today and pull the bumper support back out to it's original shape. The bumper cover you can pick up for anywhere from $75-125 online. Fill me in and I'll tell you what I did and what worked and what didnt. If you already solved your problem, share some solutions?

Jul 26, 2008 | 1997 Dodge Stratus

Not finding what you are looking for?
2003 GMC Yukon Denali Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides