Question about 1994 Toyota Camry

1 Answer

How in the world do you get a new rear passenger side door glass back in after removing the broken pieces of one that was shot out with a bb gun?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 6,826 Answers

Well, take the door panel off, and slide the new glass in after vacuuming out all those little pieces of glass with a vacuum cleaner. Installation, should be similar to replacing good glass.

Posted on Jul 04, 2010

  • 2 more comments 
  • ronlemire
    ronlemire Sep 20, 2012

    are there locking clips or how is the glass held in place? this the sliding door, not the vent window.

  • Duane Wong
    Duane Wong Sep 20, 2012

    there are usually rivets or clips you will see on the window regulator channel.

  • Duane Wong
    Duane Wong Sep 20, 2012

    the new glass window has holes that are used with a rivet or other fastener to keep it attached to the up and down moving regulator.

  • Duane Wong
    Duane Wong Sep 20, 2012

    rivets rather than rivet.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install replacement window on passenger side


you take off the door panel by using a panel clip tool to pop the clips for the panel to come off also check for any screws holding the panel to the door by the inside door handle the bottoms of the panel once you get it off unplug the window door switches to move the panel out of the way but first lower the window track so you can see it remove the weather seal plastic and then when you can get to the track and the glass you'll see that there should be yellow circle clips that pop together to hold the glass with rivets I'm assuming the glass is broken and this might have come off and is in the bottom of the door use these for the new glass after drilling out the old rivets snap them together one on each side of the new glass and then put bolts and nuts on to tighten or use a rivet gun to the track reconnect the switches for door window power and raise the glass

Feb 22, 2015 | 2004 Ford Taurus

1 Answer

Why rear windows on 2001 chevy tracker won't work ?


Would seem your into the inner doors & have a partial
grasp on things

Now you fix all door windows one shot

#1 Test all switches,ohm meter unplugged or volt meter with power
#2 Test all motors with battery voltage direct -- DC motor will run either direction-- can't hook up wrong
#3 Window Regulators -you know about them (Unless they are broken-you said they are tight)
#4 Do you have good ground side wiring & battery voltage at all
switches & motors
#5 Last resort--unhook the cables & work on freeing up the
glass & window guides etc then you will have found out if the
regulators are the issue

Aug 16, 2014 | 2001 Chevrolet Tracker

1 Answer

1996 cadillac deville how to replace passenger front door glass


remove interior door panel inside you will see where it mounts to should be two to three bolts and possible a clip that holds it in place remove old glass and install new glass from top of door remount into window gear mechanisim

May 20, 2013 | Cars & Trucks

1 Answer

How do i replace rear passenger window


Did they break the larger window? or the smaller one?
The larger one is the easy one, remove the door panel, adjust the window mechanism until you can see the bolts on the bottom window track, undo these bolts and remove the old track, To fit the new window it's simply a matter of removing the side window guide rail and sliding the window in on an angle and wiggle it around until you get it inside the door, the seat it in the rail and replace the guide rail. Then bolt the window to the mechanism and re-assemble the door panel.

If it's the smaller one you need to remove the larger window first then remove the frame between the smaller and larger piece of glass, You can then replace the glass.

I would suggest calling around and you may get a good price for an expert to replace it as it is a pain to do.

Mar 13, 2012 | 2003 Mazda Protege

1 Answer

Ford Transit Connect 2010. Broken rear door window (passenger side). need to remove windsheild wiper arm off threaded shaft. Does it pry off once nut and washer are removed? Should heat or solvent be used...


There is a special tool to push on the shaft of your wiper while pulling on the wiper arm itself. A way to get around this is to put the nut on loosely and pull up on the wiper arm while tapping on the nut with a hammer. BE CAREFULL NOT TO DAMAGE THE THREADS!

The best place to get a piece of glass would be to call an auto glass business in your area. They will deal with cutting the mastic (window adhesive), removing the old window and installing the new window.
When they get done, they will gaurantee that the window will not leak.

Feb 20, 2011 | Ford Transit Connect Cars & Trucks

1 Answer

My 2007 Jeep Cherokee Laredo passenger side locks both front and rear are not working, driver side front and rear are fine. How can i fix?


look inside the rubber boot inside the drivers door, one of the wires is probably broken splice back together. Welcome to the wonderful world of jeep problems.

Nov 14, 2010 | 2004 Jeep Grand Cherokee

1 Answer

How do I realign the passenger side window?


WINDOW GLASS REMOVAL

NOTE: Window glass must be operable in order to remove door assembly carrier. Any malfunction that prevents the window (manual or power) from being lowered must be corrected before proceeding.

  • Remove door trim panel.
  • Pry out sealing plugs in door assembly carrier to gain access to window glass securing bolts.
  • Lower window until window glass securing bolts are accessible.
NOTE:
If the power window motor is not working it can be renmoved to allow the window to be slid down.

  • Loosen window glass securing bolts and carefully press glass securing clamps apart.
NOTE:
If glass is being replaced due to breakage, remove door assembly carrier and remove broken shards of glass to prevent rattling noises in door.

  • Carefully lower the window regulator.
  • Lift window glass up and pivot forward, starting at the taller end of the glass. Pivot forward towards the direction of the side mirror.
  • Place removed window glass in a secure location.
WINDOW GLASS INSTALLATION

  • Slide forward part of window glass into opening and pivot glass downward, reversing the removal proceedure.
  • Raise window regulator until window glass securing bolts are visible in access holes on door assembly carrier.
  • Gently press window in the direction of the door latch or highest part of glass and tighten securing clamp bolts.
  • Remainder of installation is the reverse of disassembly.
  • Check operation of window before final installation of door trim panel.
TIGHTENING TORQUE
Window glass securing bolts...........10Nm (89in-lb)

Jun 25, 2010 | 2000 Volkswagen Beetle

2 Answers

Need to replace a broken window on rear passenger 1999 jeep chero


This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Sep 09, 2009 | 1999 Jeep Grand Cherokee

1 Answer

99 explorer drivers side mirror vibrates


are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

  1. Remove the front door trim panel; refer to Section 501-05 .
  2. go to car-part.com for a used mirror. Page with * is cheapest seller.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
------------------------------------------------------
f9d70e9.gif
----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
4d9527f.gif

Apr 12, 2009 | 1999 Ford Explorer

1 Answer

Rear passenger side window stuck in down position


1) Yes you are right to think that it is the regulator.
2) You can repair this.

Remove the screws that hold the door panel on.
Remove the door panel. There are alot of clips on the door panel that just need to be pulled out with panel while removing.
Remove debris shield.(plastic piece between door panel and door.
The regulator will be visible at this point.
Disconnect the electrical connector from the regulator. Separate Glass from regulator. Some use clips some use bolts to hold the glass to the regulator.
Remove regulator attaching bolts.

Thats it just reverse the procedure for installation.

Aug 29, 2008 | 2006 Jeep Liberty

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...