Question about 1993 Mercury Grand Marquis
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Jack up the passengers side of the car, get a 1 1/16" wrench break loose the fitting to the manifold, hold a 24 mm wrench on the fitting to the manifold, loosen the flare nut on the tube. Then using a 10 mm socket, about 2 inches long, loosen the two nuts under the EGR valve, then take the both out, remove the vacuum hose to the top of the EGR valve, and the sensing line from the small tube. then completely remove the flare nut from the orifice fitting on the manifold. BE CAREFUL with the tube, do not bend it or break it, you may find PB blaster useful the night before on a cold engine loosen these fittings. Once the EGR valve is out, remove the orifice out of the manifold, remove the tube from the EGR valve, again be careful, mark the tube to EGR position before pulling this off, because the top fitting to EGR needs tightened before you put it back in, it will make the lower fitting difficult if you do not line it up right, dry fitting from under the car is helpful, mark it, and then tighten the top. Clean out the tube, be careful not to bend the little tube, either inside or outside the larger tube, it sticks out inside. Clean the orifice, clean the manifold face carefully not to score it, check for blockage there too. Apply anti-seize to the orifice, put it back in the manifold, then apply anti-seize to the bolts for the EGR valve, and the flare nuts both ends. Apply some silicon to the EGR valve face, just enough to hold the gasket in place, put the new gasket on, start the bolts two turns in the gasket, it will hold them in place, then start them in the manifold, then start the lower flare fitting to orifice, tighten the top bolts, and then the flare nut, connect the vacuum line, connect the sensing line. I just recently did this process, it works, if have other EGR issues, the valve is the easiest.
Posted on Oct 13, 2009
The most common problem for your car with that condition is plugged ports where the egr feeds into the intake. You must remove the throttle body and elbow between the throttle body and intake, you will see a passage that is most likely plugged. You can clean it all out with a screwdriver or similar but it must be taken apart to get to it.
Posted on Apr 05, 2010
disconnect battery,,jack car up,,put jack stand on frame,,take starter bolts out,(may not be easy),,take wires off starter,,hoped it helped,,
Posted on May 08, 2010
Wish I had a picture for but will do my best to explain. it is located in the center, upper engine area, mounted in the rear of the intake manifold. I hope this helps you and good luck.
Posted on Apr 16, 2011
Tips for a great answer:
Sep 18, 2014 | 1995 Mercury Grand Marquis
Oct 20, 2013 | 1999 Mercury Grand Marquis
Jan 24, 2013 | 2001 Mercury Grand Marquis
Mar 14, 2011 | 1989 Mercury Grand Marquis
Nov 28, 2010 | 1994 Mercury Grand Marquis
May 08, 2010 | 1993 Mercury Grand Marquis
May 05, 2010 | 1995 Mercury Grand Marquis
Apr 05, 2010 | 1993 Mercury Grand Marquis
Sep 13, 2009 | 1993 Mercury Grand Marquis
366 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: