Question about Chevrolet Corvette

Open Question

Procedure for removing power motor antenna on C5 Corvette

Posted by on

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Remove power antenna - 96 Seville

If there is a slot in the "fender hole", it unscrews with a big screwdriver If not, check for a slide clip under fender where it goes through.

Posted on Jan 17, 2009

Ad
  • 16 Answers

SOURCE: do i need to remove or disconect condenser to

I DO NOT THINK SO. IT HAS BEEN A LONG TIME SINCE I WAS UNDER THE HOOD OF A VETTE BUT I THINK YOU CAN DISCONECT IT FROM THE RAD AND SLIDE THE RAD OUT. (BE VERY CAREFUL YOU DO NOT CRIMP ANY CONDENSER LINES)

Posted on Mar 30, 2009

shannongreer
  • 75 Answers

SOURCE: Antenna mast broken

    Give these instructions a shot. Might be too generic but might be enough to get you going. Removing Original Antenna
  1. Step 1 Activate the antenna switch to the up position.
  2. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Step 3 Gain access to the underside of the area where the antenna is located.
  4. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Step 5 Remove the mast.
  6. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Step 7 Remove the ground lead from the panel.
  8. Step 8 Pull out the antenna coaxial cable.
  9. Step 9 Unplug the coaxial from the extension coaxial cable.
  10. Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.
    Installing the New Power Antenna
  11. Step 1 Inspect the fender area where the antenna mast will be mounted for rust.
  12. Step 2 Clean the area before installing the new antenna.
  13. Step 3 Plug the new antenna coaxial cable to the extension coaxial cable. (On some General Motors and Ford cars you may need an adapter to mate the 2 cables together. Car audio retail stores sell such an adapter.)
  14. Step 4 Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  15. Step 5 Connect the power lead of the antenna to the power antenna lead on the radio.
  16. Step 6 Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  17. Step 7 Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  18. Step 8 Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  19. Step 9 Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  20. Step 10 Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  21. Step 11 Stop the motor after the cable goes into the housing 12 to 25 inches.
  22. Step 12 Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  23. Step 13 Replace the retainer nut to the base of the antenna mast and secure tightly.
  24. Step 14 Replace the panel that covers the antenna mount area.

Posted on May 13, 2009

  • 232 Answers

SOURCE: a/c blower motor for 2003 corvette

Yea leafs and other debris can get in and cause the noise. Remove the blower, thoroughly clean the fins and reinstall. This should take care of the noise.

Posted on May 15, 2009

  • 27 Answers

SOURCE: power antenna motor on my 3000gt is out and i need instructions

if it just makes a nasty clicking grinding noise then you just might need the new plastic gear strip the goes up into the antena itself. these are available as a seperate part and not too expensive and easily replaced. take the motor out and take the mast out and see if there's broken teeth in the
plastic
take a look on ebay.
http://cgi.ebay.com/ebaymotors/Mitsubishi-3000GT-1991-1999-Power-Antenna-MAST-NEW_W0QQcmdZViewItemQQ_trkparmsZ65Q3a12Q7c66Q3a4Q7c39Q3a1Q7c72Q3a1171Q7c240Q3a1318Q7c301Q3a1Q7c293Q3a1Q7c294Q3a200QQ_trksidZp3286Q2ec0Q2em14QQhashZitem3a5025016eQQitemZ250452705646QQptZOtherQ5fVehicleQ5fPartsQQsalenotsupported

Posted on Jun 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 corvette C5 has some clear to pink tinged


check cooling system or power stering lines

Oct 18, 2014 | 2002 Chevrolet Corvette

1 Answer

How to remove antenna wire on the rear deck glass of a 1998 chevy corvette


I think the antenna wire is permanently attached to the glass and plugs into the power antenna motor

Oct 17, 2014 | 1998 Chevrolet Corvette

1 Answer

Antenna goes up not down 91 crovette


Sounds like you need "91 Corvette power antenna mast and cable" I replaced mine 4 years ago for 34.00 on Ebay. you might do a search on CORVETTE Power Antenna MAST 1988-1992 + How 2


They have it for $21.99 + $5.00 shipping. Or just search on ANTENNA MAST, there are 2,700 matches for this search.


necss03

Oct 16, 2010 | 1991 Chevrolet Corvette

1 Answer

INEED TO REPLACE THE POWER ANTENNA IN MY 2000


Hello, i've just checked in the procedure (25 steps in all to take it out, that's a lot!!!) for a antenna replace for you're corvette and would recomand you to go to a dealer to get the antenna replace. You may think it will be caustly but those guys know how to take it appart and won't fool around like any other mecanic that won't have the procedure. I would not recomend you to do it you're self since the procedure requires you to take most of the back end of the car appart. But if you still feel corageous, send me a message and i'll post the procedure for you.

Oct 24, 2009 | 2000 Chevrolet Corvette

2 Answers

Antenna will not go up or down,but still has


Have the antenna motor tested re place it if not working if antenna motor is working you will need a new antenna mast and antenna cable to remove this unscrew the washer nut at the base of the antenna and turn radio on antenna should push up and play out he cable to replace insert new cable and turn radio off it will draw cable in and antenna tighten washer nut and your dne

Aug 07, 2009 | 1993 Chevrolet Corvette

2 Answers

A/c blower motor for 2003 corvette


Yea leafs and other debris can get in and cause the noise. Remove the blower, thoroughly clean the fins and reinstall. This should take care of the noise.

May 15, 2009 | 2003 Chevrolet Corvette

1 Answer

Antenna mast broken


    Give these instructions a shot. Might be too generic but might be enough to get you going. Removing Original Antenna
  1. Step 1 Activate the antenna switch to the up position.
  2. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Step 3 Gain access to the underside of the area where the antenna is located.
  4. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Step 5 Remove the mast.
  6. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Step 7 Remove the ground lead from the panel.
  8. Step 8 Pull out the antenna coaxial cable.
  9. Step 9 Unplug the coaxial from the extension coaxial cable.
  10. Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.
    Installing the New Power Antenna
  11. Step 1 Inspect the fender area where the antenna mast will be mounted for rust.
  12. Step 2 Clean the area before installing the new antenna.
  13. Step 3 Plug the new antenna coaxial cable to the extension coaxial cable. (On some General Motors and Ford cars you may need an adapter to mate the 2 cables together. Car audio retail stores sell such an adapter.)
  14. Step 4 Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  15. Step 5 Connect the power lead of the antenna to the power antenna lead on the radio.
  16. Step 6 Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  17. Step 7 Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  18. Step 8 Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  19. Step 9 Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  20. Step 10 Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  21. Step 11 Stop the motor after the cable goes into the housing 12 to 25 inches.
  22. Step 12 Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  23. Step 13 Replace the retainer nut to the base of the antenna mast and secure tightly.
  24. Step 14 Replace the panel that covers the antenna mount area.

May 13, 2009 | 1993 Chevrolet Corvette

1 Answer

98 corvette 5.7 eng., harmonic balancer needs replacing!


Crankshaft Balancer: Service and Repair
REMOVAL PROCEDURE
1. Disconnect the negative battery cable.
2. Release the accessory drive belt tensioner (3).
3. Remove the drive belt (5) from the engine.
4. Remove the power steering gear from the vehicle.
5. Remove the starter motor.
6. Remove the power steering cooler bolts from the front crossmember.
7. Remove the power steering cooler from the front crossmember and reposition.
8. Release the air conditioning (A/C) belt tensioner (10).
9. Remove the A/C drive belt (1) from the engine.
10. Remove the crankshaft balancer.
INSTALLATION PROCEDURE
1. Install the crankshaft balancer.
2. Install the A/C drive belt (1) to the engine.
3. Install the power steering gear.
4. Install the power steering cooler to the front crossmember.
5. Install the power steering cooler bolts.
^ Tighten the power steering bolts to 11 Nm (97 inch lbs.)
6. Install the starter motor.
7. Lower the vehicle.
8. Install the accessory drive belt (5) to the engine.
9. Connect the negative battery cable.
^ Tighten the negative battery cable bolt to 15 Nm (11 ft. lbs.).
10. Program the Transmitters.

May 11, 2009 | 1997 Chevrolet Corvette

1 Answer

1999 corvette c


Very easily, take off the passenger side tailight (outter) two screws/torque bit. Once you have done that reach in on the inner quater panel you should be able feel the antenna....... (To remove anntenna). From the outside of the anntenna on top where the actual anntenna comes out there is a ring silver or balck. You should be able to twist (unscrew) that ring to loosen the antenna and two more on the in side of quater panel. The anntenna should drop from the inside of the quater panel. Hope this helps!!

For visual instructions go to: #17

http://forums.corvetteforum.com/c5-tech/1817090-the-ultimate-diy-thread-with-pics.html


Aug 02, 2008 | 1999 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

475 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...