Question about 1994 Ford Econoline

1 Answer

Key wont go into ignition cylinder lock how to change switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 541 Answers

First take steering out, use puller, then press on small button over cylinder to get out. usually you'll need the key in to get out. i realize that that is your problem. drill that button out with drill bit that will fit in the hole. it holds the cylinder in place ! then install cylinder using ignition key, you gotta turn it if i remember and re-install everything in reverse procedure

Posted on Jul 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 ford explorer changed ignition now wont start


If your vehicle was towed, check the fuel pump intertia switch located near the top of the passenger side kick panel.
if you changed the key, you will be having an antitheft problem.
you could try putting an original key at the lock cylinder while turning the new key, it may allow it to start... if so, new key will require programming, or have the new lock cylinder coded to the old keys.

Jun 19, 2014 | 1999 Ford Explorer

2 Answers

Keyless entry wont program on my malibu 2000


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch to UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones). 11. Remove the ignition key in order to exit the Program Mode.

May 08, 2014 | 2000 Chevrolet Malibu

1 Answer

Car wont start when turn off changed battery/nuetral switch


try another key. the key could be worn where read coil in the ignition switch lock cylinder and immobilizer control module and ecm dont recognize ignition key or ignition switch key lock cylinder failing.

Nov 13, 2011 | 2002 Kia Spectra

1 Answer

1997 pontiac grand prix- car wouldn't start so we changed the alternator and charged the battery. it still wont start and now the key wont come out of the ignition.


Hello! The problem is the ignition lock cylinder itself...I would suggest changing the cylinder and the ignition switch...Purchase and change the Lock Cylinder first...If that solves the problem, stop there (The switch is costly...It may not be needed)...See photos below...Guru....Saailer


saailer_61.gifTurn the key to start ..1/16" Allen into the hole on top of the lock assembly to release the retaining pin...Turn to run...remove

saailer_62.gif

saailer_63.gif

saailer_109.jpgACDELCO Part # D1405D moreinfo2.png {#12369498} PART REQUIRES CODING AT GM DEALERSHIP....Cost $10

saailer_110.jpgColumn Shift...STANDARD MOTOR PRODUCTS Part # US422 ...Cost $100

saailer_111.jpg
STANDARD MOTOR PRODUCTS Part # US264With console shift...Cost $90

Jan 28, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

How do you change a key switch in a 2001 chevy impala, the factory keys wont turn in the switch


If your key is worn try getting a new one cut.
The ignition lock cylinder and keys do not contain any coded electronic components. The lock cylinder housing contains the coded electronic components. Changing an ignition lock cylinder or replacing a key is a purely mechanical process which does not affect the vehicle theft deterrent system. To replace an existing key, simply cut a new key to match the existing one. If no keys are available, the lock cylinder must be changed. To change the lock cylinder, simply replace the existing lock cylinder with one of the same type.
If you are unable to operate the ignition cylinder with a new key then you will probably need to replace the cylinder and switch.Replacement of the switch involves reprogramming
The system may be programmed with or without a scan tool.
There is a way to get the cylinder out without replacing the switch but this procedure should be performed by a qualified GM technician as it involves removal of the switch and some precise drilling.

Nov 01, 2009 | 2001 Chevrolet Impala

1 Answer

I need to change my ignition lock cylinder but i cant turn the ignition switch lock cylinder to the ON position. What do i do?


well is it that the key wont turn or dont have key? you can drill out the lock use a big bit it will distroy the tumblers so you can use a screw driver turn it and pull out

Jun 04, 2009 | 1998 Pontiac Grand Prix

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

2 Answers

Ignition switch in a 1995 ford taurus


Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Jan 27, 2009 | 1995 Ford Taurus

1 Answer

Ignition key switch


You have to use a pin or paper lip to insert in hole in igmition switch to release the lock cylinder. The key has to be in "on" position I think.

Removal
  1. Disconnect battery ground cable (14301) .
  1. Turn lock cylinder key to RUN position.
  1. Place a 3.17mm (1/8-inch) diameter wire pin or small drift punch in hole in upper steering column shroud (3530) under ignition switch . Press retaining pin while pulling out on ignition switch to remove it from lock cylinder housing (22074) .
Installation
  1. Install ignition switch by turning it to RUN position and pressing retaining pin. Insert ignition switch into lock cylinder housing . Ensure ignition switch is fully seated and aligned in interlocking washer before turning key to OFF position. This will permit cylinder retaining pin to extend into lock cylinder housing hole.
  1. Rotate ignition switch, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.
871404a.gif

Jan 13, 2009 | 1986 Ford Mustang

Not finding what you are looking for?
1994 Ford Econoline Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...