Question about 2008 Chevrolet Cobalt

Open Question

How do I remove the center console panel to access the bcm - 2008 Chevy Cobalt

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 54 Answers

SOURCE: I need to remove door panel on 2008 Cobalt

There are about five or six screws on the panel, the rest of it is snap on. You will have to pull the door panels off the door with a flathead screwdriver.

Posted on Dec 02, 2008

  • 51 Answers

SOURCE: Low Beams Stay On

Also, the daytime driving lights are controlled by relay. It's possible the relay may have melted down inside and is shorted, remaining on even when primary ignition power is off. The relay runs about $15.00 to $20.00 USD and might be worth a shot to replace. Likely you can get one at a recycling yard for a dollar or two.

Posted on Feb 07, 2009

  • 10 Answers

SOURCE: I need to remove the front headrest of a 2008 chevy cobalt lt

Push the button and pull up on it at the same time

Posted on May 25, 2009

  • 1986 Answers

SOURCE: removing passenger door panel on chevy cobalt

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 12104 Answers

SOURCE: 2005 chevy cobalt, car wont start ... check

have car scanned for trouble code some auto stores such as auto zone---advanced auto scan for free the code[s] will give u a start point towads correcting ur problem

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are all the ground wires located on a 2008 chevy cobalt?


It wouldn't be a ground problem If it were the whole instrument cluster would be dead . Checking the BCM an the IPC for DTC'S - diagnostic trouble codes is the proper way to diagnose this type problem . Not worrying about grounds .
Odometer
The vehicle odometer is calculated and stored electronically in the body control module (BCM) and is sent via the serial data circuit to the instrument panel cluster (IPC) for display. The BCM calculates and stores the mileage based on the vehicle speed serial data information from the PCM/ECM. The IPC displays the season odometer information from the BCM in the driver information center (DIC). The odometer will display error if the IPC detects an invalid odometer data from the BCM. After an invalid odometer data is received from the BCM, the IPC will display the last known odometer reading for 1.5 seconds before error is displayed in the DIC.
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed based on serial data message from the body control module (BCM). The BCM receives vehicle speed data from the PCM/ECM via the serial data circuit. The speedometer will default to 0 km/h (0 mph) if:
• The PCM/ECM detects a malfunction in the vehicle speed sensor circuit.
• The BCM detects a loss of serial data communications with the PCM/ECM.
• The IPC detects a loss of serial data communications with the BCM.

Your best bet would be to take it to the dealer !

Apr 19, 2017 | 2008 Chevrolet Cobalt

1 Answer

Where can I find the radio fuse for my 2008 Chevrolet HHR


The fuses should be located in bcm. The bcm access panel should be on the right side of center console.
The wiring diagrams were with and w/o amp. I didn't know which one you had.
bcm radio fuse-ro2wwa544o4fmhiuvvmipigf-5-0.jpg

Mar 04, 2017 | 2008 Chevrolet Hhr

1 Answer

What is the radio fuse for 2009 colbalt


RDO fuse # 23 15A located in the BCM fuse box . Plastic cover on the right side of the center console comes off , pull ! BCM fuse box behind it .

Dec 25, 2016 | 2009 Chevrolet Cobalt

1 Answer

Where is the Hazzard flasher found in a 2008 Chevy Cobalt?


My searches indicate that it is not in the fuse box where it should be. The flasher relay is shown under the left side of the dash console, but then I found this.

The Chevy cobalt does not have a flasher relay, the cobalt turn signals are fully solid state and run through the PCM (powertrain control module) in the car, the sound comes from your speaker in the front left.
http://www.fixya.com/cars/t26193585-4_ways_flasher_located_in_2008_chevy


http://wiringmanuals.blogspot.ca/2014/08/2008-chevrolet-cobalt-engine.html#more
Wiring Diagrams and Free Manual Ebooks

May 13, 2016 | Cars & Trucks

2 Answers

Where can I buy light for Chevy cobalt gear shift console


Most console bulbs are 194. Napa or any parts store.

Apr 14, 2015 | 2008 Chevrolet Cobalt

1 Answer

Fuse box location 2005 chevy cobalt


There are two locations for fuse boxes on a 2005 Cobalt. 1) is under the hood, on the driver's side, under the jump start contact. 2) is inside the center console, on the right side. The forward part of the console kick panel has a press-opening panel, which, when removed, reveals the fuse box.

Jul 14, 2014 | 2005 Chevrolet Cobalt

1 Answer

Where is the air bag module ona 2008 chevy cobalt located?


Underneath the carpet under the center counsole

Oct 14, 2012 | 2008 Chevrolet Cobalt LS

1 Answer

I am trying to find the location of the fuses for the brake lights on a 2006 Chevy Cobalt sedan


{: ) The stop lamp switch controls the on/off function of the stop lamps including the center high-mounted stop lamp( CHMSL). The stop lamp switch get its power from the Body Control Module (BCM). This power is also fused but is internal to the BCM. You need to check carefully the voltages at the stop lamp switch and its on/off function. If voltage is not present at the stoplamp switch, you can check the C4 connector(light gray in color) at the BCM if there is some loose connection. Otherwise the BCM may not be giving an output voltage and will need to be repaired/replaced. I hope the problem is not caused by the BCM.

Aug 01, 2011 | 2006 Chevrolet Cobalt

1 Answer

How do I remove a hubcap from a 2008 Chevy Cobalt. Do I need to remove all of the lug nuts or the center cap?


most hubcaps are springclip loaded! some are mounted inside the center cap! some are held on by the lug nuts! pull the center cap first, and look for a screw that holds it on! if not, then remove the lug nuts!

Mar 07, 2011 | 2008 Chevrolet Cobalt

1 Answer

I need to remove the front headrest of a 2008 chevy cobalt lt


Push the button and pull up on it at the same time

Apr 04, 2009 | 2008 Chevrolet Cobalt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

686 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...