Question about 1997 Mazda MPV

1 Answer

My friend bought new parts for his mpv and decided to buy a new car and still has the new parts, I was wondering if can I use front end parts from 1993 for a 1997? lower ball joint and CV?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 14,036 Answers

NOPE THERE MAY BE A DIFFERENCE.I WOULD BUY PARTS FOR A 1997 MODEL 1993 MODEL IS 4 YEARS APART.CAR MANUFACTORYS CHANGES A LOT PARTS MAY BE DIFFERENT I WOULD NOT TAKE THAT CHANCE.

Posted on Jul 04, 2010

Testimonial: "thank you...feed back is correct. Parts are different."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the pcm in a 2000 mazda mpv?


You can't test it, you decide if it is the problem by exhausting all other diagnostic possibilities before the $1000.00 part is replaced. The failure rate of this part is less than 2%, so be very careful that you are sure it is the problem.

Sep 04, 2012 | 2000 Mazda MPV

1 Answer

How do I remove fuel level sensor from a 1998 mazda mpv.


it is inside the gas tank, attached to the fuel pump. you might be better off buying an entire new
pump/sender unit and swapping it in when you remove the old one. Both are now 13 years old and past the end of their designed life. buy a new ring gasket for the top of the tank and do it too.

Mar 07, 2011 | 1998 Mazda MPV

1 Answer

I have a 91 toyota mr2 which need to change the clutch line from clutch master cylinder to slave cylinder. Where can i get the aftermarket parts? or i can just replace the rusty part, but where can i get...


I hate this particular project. Yes, you need metric ends at least. The problem of course is that auto parts stores don't carry long lines with metric ends. I ended up getting a "pipe flaring tool" so that I could put my own metric ends on the standard pipe. I then bought a short 7" metric line from a parts store, and cut it to use the ends on new standard size line. You will either want to get a nice one on loan from a friend or take the car to a shop. The cheap $30 tool I bought at one of the big auto parts stores didn't even work correctly out of the box. Ended up buying a $150-200 one that works great! Still a lot of work and expense if you are doing it yourself. The line is hard to get to once it gets up to the front of the car, so cutting out the bad rusty part and putting ends on is the easier do-it-yourself project - if you have the brake line flare tool. I would take it to a shop. Good luck!

Nov 11, 2010 | 1991 Toyota MR2

2 Answers

My 2000 2wd expedition is makin a squeakin noise under the front end from the suspension. it does it when i turn the wheel or hit a dip in the road it even does it when i sittin still. a friend said my...


Your friend is a little vague but almost right. This is due to lack of lubrication in the lower ball joints. Common issue. There is no way to fix other than replacement. the parts I am recomending are a little more pricey but do wonders and "FIX" the issue. They are called "Moog problem solvers". In my opinion of doing front end work over the years, Moog has some of the best products for issues with front end repair. Often correcting manufacturer issues!! Have the front end components inspected for wear and then replace the lower ball joints definately. Let me know if you need anything else.

Aug 17, 2010 | 2000 Ford Expedition

1 Answer

Need to buy a battery, spark plugs and Injectors for my 1989 MPV Mazda. So would appreciate the parts numbers and descriptions to buy the correct ones. Thanks. Sorry, forgot to add the belts that go in...


Just go to the autoparts store to get the parts. Make sure you have the make/model of the car, the engine size, and whether it has a/c or not. They will look them up on the computer and get the parts for your specific vehicle. If you register your vehicle at autozone.com, you will have access to a free full onlline repair manual for your vehicle. It's free and handy! Hope this helped.

Jul 18, 2009 | 1989 Mazda MPV

2 Answers

94 honda civic cat back replace with no hydraulic lift


I would use floor jacks and jack it up from the back as high as it will go and then set jack stands under it. Its front will drive so you dont have to worry about it rolling just make sure its in park and if its standard make sure its in gear. Be good to block the front wheels also.

Jul 10, 2009 | 1994 Honda Civic

1 Answer

1990 mazda mpv power steering pressure switch


You can try a junk yard or better yet the dealer for new.

May 09, 2009 | 1990 Mazda MPV

1 Answer

1998 mazda mpv 4x4 is not engaging and awd light is blinking wondering what i can check


If your system is like my old 91 there was a relay and vacuum actuated switches. My problem ended up being one of those relays being bad. There were 2 relays and they had the identical part numbers so to test it I switched the wires from one relay to the other and it went into 4wd. Might be an easy fix. Check your manual and see what makes it go into 4X4. If you dont have a manual see if you can download your models manual at www.pdftown.com I think that my series was similar to yours so look on the firewall on the left side by the strut tower. You will see 2 sets of wires going up into rubber boots. The relays are in the boots. It took me quite a wile to figure it all out but the transfer case has a little motor and some contacts inside the end of the transfer case housing. Thats is where the magic happens but the relays are what make the magic happen. There are also vacuum switches on the drivers side strut tower. One engages the front end and one disengages the front end. There is a vacuum actuated system that works the front end and if the rod or vacuum goes bad and the system sees that the front end didnt engage this will also give an error. I would start at the transfer case relays first. Like I said, it is what gave me your exact described problem. Hope this helps... and dont forget to rate the fix. Thanks... Dale

Mar 16, 2009 | 1998 Mazda MPV

2 Answers

2000 Mazda MPV


I NEED THE DIAGRAM FOR SERPENTINE BETL FOR MAZDA 2000 MPV

May 17, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
1997 Mazda MPV Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...