Question about Ford F-150

1 Answer

My homelink system keeps blowing the fuse why?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,427 Answers

Once a fuse is blowing its cause of 2 things..

1.) the device its connected too is pulling more amperage than the fuse is,, for example the fuse is 10 amp but the device pulls 15,, to fix this increase the amperage of the fuse by 5 amps

2.) a wire is grounding off causing a short circuit.. Trace the power wire inspect got breaks or shorting on eighter the body or anther wire.. replace wire..

Posted on Jul 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you program the garage door buttons in a 2009 Porsche 911


The control is made by HomeLink. You can find instructions on how to program your specific type of garage door here:

http://www.homelink.com/program

Here are the basic steps for a "Genie" garage door opener:

  1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash, which may take up to 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)
  2. Press the appropriate HomeLink button I, II or III which you want to train and keep holding it until the indicator light starts flashing slowly. Once the indicator light starts flashing slowly, you may release the button. HomeLink is now in "training mode."You will now have 5 minutes to train your hand-held transmitter to the HomeLink transmitter in the bumper.
  3. Stand in front of your vehicle with the original hand-held transmitter for the garage door opener (or other device) that you wish to train.The transmitter unit to be trained is located in the bumper about 4 inches to the left of the vehicle's center.
  4. Hold the original hand-held transmitter between 0-12 inches from your car's bumper. NOTE: The distance between the hand-held transmitter and the HomeLink transmitter unit in the bumper depends on the system being trained. It may require several attempts at different distances in order to pick up the signal.
  5. Now press and hold the button on your original garage door transmitter while keeping your fog lights in view. The fog lights will blink three times to indicate that the training has been successful.NOTE: If the training time exceeds the five minutes, the fog lights blink once. If this happens, you should repeat steps 2 to 5.
  6. Press and hold the trained HomeLink button and observe the indicator light.
    • If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
    • If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with Steps 7-9 for a rolling code device. A second person may make the following steps easier. Please use a ladder or other device; do not stand on your vehicle to perform the next steps.
  7. At the receiver (motorhead unit) in the garage, locate the "learn" or "smart" button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener's manual.
  8. Press and release the "learn" or "smart" button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, you have approximately 30 seconds to initiate the next step.
  9. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the "press/hold/release" sequence up to 3 times to complete the training process.

Jan 14, 2013 | 2008 Porsche 911

1 Answer

Over head lights and homelink garage door system quit working suddenly. all fuses intact


Check your fuses and relays in your controller and your house unit. probbaly a blown fuse.

Oct 19, 2010 | 2004 Nissan Quest

2 Answers

How to program my cars garage door opener buttons for my garage door.


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

May 15, 2010 | 2001 Nissan Altima

1 Answer

How do you program the homelink system with a new


Homelink has this information available for free on their website.
The procedure is fairly easy however it varies depending on what functions you want programmed and if your opener has "rolling code technology".
Here is the website www.homelink.com.
Good luck

Mar 10, 2010 | 2009 GMC Acadia

1 Answer

2005 honda odyssey homelink programming


If you just received your vehicle and have not trained any of the buttons in HomeLink before, you should erase any previously learned codes before training the first button. To do this, press and hold the two
outside buttons on the HomeLink Transceiver for about 20 seconds, or
until the red indicator flashes.
Release the buttons, then go to step 1.
If you are training the second or third buttons, go directly to step 1.

1. Unplug the garage door opener motor from the electrical outlet.
2. Hold the end of the garage door opener remote 2 to 5 inches from HomeLink. Make sure you are not blocking your view of the red indicator in HomeLink.
3. Press and hold the remote transmitter button and one of the HomeLink buttons at the same time.
If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 5. If the red indictor in HomeLink continues to flash slowly (does not flash rapidly), your remote transmitter may stop transmitting after a short time. Go to step 4.
4. Press and hold the remote transmitter button and one of the HomeLink buttons at the same
time. While continuing to hold the HomeLink button, press and release the remote transmitter button every 2 seconds. If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 5. If the red indicator in HomeLink continues to flash slowly (does not begin to flash rapidly), repeat steps 2 thru 4.
5. Plug in the garage door opener motor, then test the HomeLink button by pushing it for about 1
second. If the button works, programming is complete. If the button does not work go to step 6.
6. Push and hold the HomeLink button for a few seconds, then watch the red indicator on HomeLink.
If the indicator stays on or flashes slowly, repeat steps 2 thru 5. If the indicator flashes rapidly
for 2 seconds then stays on, you have a rolling code transmitter. Go “Training with a Rolling Code System”
7. two HomeLink buttons to operate any other compatible remotely controlled devices around your
home (lighting, automatic gate, security system, etc.).
Repeat these steps to train the other

Jan 05, 2010 | 2006 Honda Odyssey

1 Answer

Homelink


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Apr 17, 2009 | 2000 Mercedes-Benz CLK

1 Answer

I need to know the process on how to program the cars built in gurage door opener on a 2001 chrysler town & country


Hi my name is Allen!

Program a previously trained homelink button as follows... 1. Press and hold the desired pre-programmed HomeLink button for at least 20 seconds (but no longer than 30 seconds) until the indicator light begins to flash. Without releasing the HomeLink button, position the hand-held transmitter 1-3 inches away from the homeLink surface keeping the HomeLink indicator light in view. 2. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button (or press and "cycle" - as described in "Gate and Canadian programming"). DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful programming) The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed. however, it may be necessary to follow steps 5-7 of the "programming" section to complete the rolling code training. This procedure will not affect any other programmed HomeLink buttons.

Dec 20, 2008 | 2001 Chrysler Town & Country

2 Answers

How to set up for 2005 pacifica garage door opener


how about a real answer......

1. Press and hold the two outer HomeLink buttons, and
release only when the indicator light begins to flash (after
20 seconds). Do not hold the buttons for longer than 30
seconds and do not repeat step one to program a second
and/or third hand-held transmitter to the remaining two
HomeLink buttons.

2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while
keeping the indicator light in view.
3. Simultaneously press and hold both the HomeLink
button that you want to train and the hand-held transmitter
buttons. Do not release the buttons until step 4
has been completed.

4. The HomeLink indicator light will flash slowly and
then rapidly after HomeLink successfully receives the
frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from the
slow to the rapid flash.
5. Press and hold the just trained HomeLink button and
observe the indicator light. If the indicator light stays on
constantly, programming is complete
and your device
should activate when the HomeLink button is pressed
and released.

Dec 11, 2008 | 2005 Chrysler Pacifica

2 Answers

Honda Pilot 2005 garage door programming


Hi,welcome . Homelink has a website and phone number for programing help contact.
HomeLink at 800-355-3515 or visit their
website at www.homelink.com. they have a very good support system to hep you with problems.

Nov 13, 2008 | 2005 Honda Pilot

1 Answer

Homelink garage door opener


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

ALSO GOOD GUIDE FOR TROUBLE SHOOTING.

HOPE THIS HELPS

Jul 23, 2008 | 2004 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...