Question about 1989 Mazda B-Series

Open Question

Crankshaft seal installation difficulty

How hard is it to replace crankshaft seal on a 1989 mazda b2600?

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
samtoler
  • 666 Answers

SOURCE: b2600 white smoke coming out of exhaust

i`ve never heard they are interchangeable, Are you sure its the head? i would inspect the #1 cylender a little further for a hair line crack

Posted on Jun 09, 2010

Ad
  • 365 Answers

SOURCE: i need to set up the camshaft timing marks on a 1994 mazda b2600

its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the front wheel bearings on a 2004 mazda bravo, b2600. Inner seal flush with rotor or firm against bearing?


the seal is flush with the edge of the hub and should be free from the bearing if where the seal is fitted is deeper than the width of the seal that may be that the manufacturer can use two different seal makes that have two different thick measurements

Aug 29, 2015 | Mazda Cars & Trucks

1 Answer

How do I replace a clutch from a 1989 Mazda b2600 4wd


You'll need to either take out the transfer box or the prop shaft to the transfer box, remove the gearbox by unbolting and then you'll have access to the clutch. Make sure you have a clutch locator tool handy for the new parts to line up to make getting the gearbox back on easier

Oct 07, 2014 | Cars & Trucks

1 Answer

1989 mazda b2600 oil coming out of front seal from hole in toming cover


More info would be helpful ......With that little info I can only say replace the front seal and timing cover gasket....Really need to know mileage..,has it been serviced lately.....and so on...

Feb 19, 2014 | 1989 Mazda B-Series

1 Answer

Are mazda B2600 gearbox same to Mitsobishi. Can I replace Mitsobishi gearbox on Mazda B2600..1992?


Mazda and Ford parts will change,your B2600 with swap out with a 92 Ford Ranger.

Dec 25, 2012 | 1992 Mazda B-Series

1 Answer

Mazda b2600 charge light on and not charging changed alternater and fuseable link but no go


Then you have a field problem without the field you wont charge B2600 uses a voltage regulator it at the side of the fire wall it a square metal box either you adjust or replace it

Aug 21, 2011 | Mazda B2600 Cars & Trucks

1 Answer

I need to set up the camshaft timing marks on a 1994 mazda b2600


its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Jun 11, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

How do i take out a rear main seal?


Remove the transmission, after holding the rear of the engine supported, using a jack with a piece of wood between it and the engine. Remove the clutch and pressure plate, and the flywheel or if automatic, the flex plate. The rear main seal retainer will then be exposed. Remove the 2 oil pan to main seal retainer assembly, and the bolts circling the retainer, and slide the retainer assembly unit back off the crankshaft. Remove the old gasket from the retainer, and clean the gasket ridge before installing a new gasket. It's a one piece hard rubber gasket, which must be inserted in the retainer evenly. This can be done on a work bench, or flat wood on a concrete floor, Some light oil might help it seat easier, Once seated slide the retainer containing the new gasket back over the rear of the crankshaft, A rubber hammer will help ease it back into position, Replace all bolts, not forgetting the oil pan to retainer bolts, and reinstall all parts in reverse order of removal. If a manual trans, this would be an excellent time to install a new clutch kit.

Jan 11, 2010 | 1989 Mazda B-Series

1 Answer

Front crankshaft seal, 1989 hilux


Hello,

Yes, it's possible to change the seal after removing the balancer.
If the balancer shows signs of scratching, wear at the place of the seal, change that part too!

To remove the old seal, drill 2 small opposite holes in the seal flange ( there is metal in it ).
Screw 2 (parker) screws in the holes, so you can pull the seal out gently.
Grease the new seals' inner race, and put some sealant paste to the external race.
Push it back in place with a wooden piece ( drill a hole in the center for the crankshaft end )
Grease the outher race of the balancer. This will help the seal come gently into place.

Good luck!

Nov 01, 2009 | 1989 Toyota 4Runner

1 Answer

1989 Mazda B2600i pickup overheats. Replaced


you just said it you need a new fan clutch

Mar 20, 2009 | 1988 Mazda B2600 Cab Plus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...