Question about Honda Accord

1 Answer

My 1986 honda accord ecu is flashing 6 times what code is this

Posted by on

  • litetackle Jul 03, 2010

    Thank you I printed the page for later reference

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Error code 6 temperature sensor problem

Code 0 and 11 Electronic Control Module (ECM)
Code 1 Heated oxygen sensor A
Code 2 Oxygen content B
Code 3 and 5 Manifold Absolute Pressure
Code 4 Crank position sensor
Code 6 Engine coolant temperature
Code 7 Throttle position sensor
Code 8 Top dead center sensor
Code 9 No.1 cylinder position sensor
Code 10 Intake air temperature sensor
Code 12 Exhaust recirculation system
Code 13 Barometric pressure sensor
Code 14 Idle air control valve or bad ECM
Code 15 Ignition output signal
Code 16 Fuel Injector
Code 17 Vehicle speed sensor
Code 19 A/T lock-up control solenoid
Code 20 Electric load detector
Code 21 V-TEC control solenoid
Code 22 V-TEC pressure solenoid
Code 23 Knock sensor
Code 30 A/T FI signal A
Code 30 A/T FI signal B
Code 41 Heated oxygen sensor heater
Code 43 Fuel supply system
Code 45 Fuel supply metering
Code 48 Heated oxygen sensor
Code 61 Front heated oxygen sensor
Code 63 Rear heated oxygen sensor
Code 65 Rear heated oxygen sensor heater
Code 67 Catalytic converter system
Code 70 Automatic transaxle
Code 71 Misfire detected cylinder 1
Code 72 Misfire detected cylinder 2
Code 73 Misfire detected cylinder 3
Code 74 Misfire detected cylinder 4
Code 75 Misfire detected cylinder 5
Code 76 Misfire detected cylinder 6
Code 80 Exhaust recirculation system
Code 86 Coolant temperature
Code 92 Evaporative emission control system

Posted on Jul 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 honda no spark


1 one spark plug or all 4? (key fact one missing)



insert honda OBD1 diagnostic jumper (or as FSM directs)

engage Diag mode.

then crank engine for 5 seconds.

then release key,

does the ECU flash out codes for a failure.,, BINGO

all cars work like this 1987 to now, USA>

what engine, of the many?







fsm quotes (and vast on line data same on all honda\'s)

there are more online facts on honda\'s than any car.

they race them and have hacked them to infinite levels.

now thequote



On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).



my comment, code 4 or 8 tells you , CKP or CMP sensors are dead.

in gringo that is "crank or cam sensors dead)

the ECU can report even , 1 in 10 pulses missing.

its very very , accurate in this report.

crank

release key

wait a minute to see if the ECU sets DTC errors.

do not turn off the key,or it erases them. wait, for 5min.

Jul 09, 2014 | 1991 Honda Accord

1 Answer

1991 honda accord turns over wont start . when key in second postion no lights on dash exept for battery light


blown fuse.
the CEL lamp must glow, or the ECU is dead. (no power)
the CEL is very important lamp telling you the ECU has power
and it thinks(sic) that it is ok, (basics)
if the lamp is burned out, it become hard to work the ECU.
as this ECU flashes codes for errors,
check all fuse. in both boxes.

Feb 05, 2014 | 1991 Honda Accord

1 Answer

How to turn the rely back on to the fuel pump


as always check all fuses FIRST (electrics issues, EFI is that.)

the Puter magic is mindboggling, but..
why not post the symptoms, ????????
is it dead fuel pump or the more accurate, low or no fuel pressure?

All ECU/PCM (EFI ) all cut the pump for many reasons.
PCM is PGM-FI , in honda speak. PCM is modern term.
first really is fuse checks. !!!
1: no spark. (did you pull the CEL DTC blink codes to see if the ECU
is unhappy?
2: many cars (you must crank to run the pump) so looking not cranking for 12v at the pump , you fail and is normal.
(2 man rule one to crank, one to listen or check voltage at pump
or pump pressure at rail or filter) (a new filter is a good ploy now)

the fsm is here, and covers this, read the FSM
some pages are missing,,, so get real FSM
or go to alldata.com
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

free but , some pages missing(good luck with free)

http://hondatech.info/downloads/Auto/Manuals/Accord/

see chapter 16, electrics.
F22A6 engine
this page is valid.
http://troubleshootmyvehicle.com/honda/2.2L-2.3L/how-to-test-the-fuel-pump-2

I like the (above) is cam dead?, line.... funny that.
(gather evidence, fuses good, cam spins (watch it) no DTC stored.
then check for spark no spark work spark now ,not fuel.
with a dead cam there is no CMP , no CMP the ECU pukes
codes for CMP Dead.
this is an interference engine so i'd bet that belt is fresh, huh?
ever 60k? per the opr; guide.

watch for codes, 4,8,9,15,16 (OBD2 DTC codes)
code 9 is dead cam. dead spark and all fuel is cut. for ever.
TDC&crank sensor, must work and not show DTC codes.

http://www.troublecodes.net/honda/hondadtc/

DTC flashing? The DLC jumper:
On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).

if fee for you , this very old car, so here is your long lost oper guide
http://justgivemethedamnmanual.com/honda/

Nov 27, 2013 | 1991 Honda Accord

1 Answer

HAVE NO SPARK OUT THE COIL


nov 6, how'd i miss this..???
not the V6 , right?
as always, check all fuses. (op guide in glove box shows em)
ok the car (USA) has a EFI system with spark too.
this EFI system has 3 parts to make spark. (not counting coil)
crank sensor (the ECU will flash a code if dead, did you looK).
ECU (unliikely but do check the DTCs lamp codes)
Dizzy
Coil.
Got code (DTC) 4,8,9,15, ah bingo?
here are the words in the FSM ( got one yet , they are free too)

On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).
end quotes



or RTM? here. free, its all there.... even simple coil tests.
but id bet its not the coil, for sure i dont know, i only tests. and then replace truly bad parts.
http://hondatech.info/downloads/Auto/Manuals/Accord/

Nov 06, 2013 | 1991 Honda Accord

1 Answer

The light on D keeps flicking when the gear is in drive and the car is being driven


non hybrid answer.....?
The TCM (tranny brain) read the operators guide. (open glove box , grab it) its free this guide. get one.
it tell you D1 flashes, and means tranny MALF.

On some cars, after 1996 the Tranny fail codes are reported
via the ECU, using any scan tool. ever use a scan tool?
see P070x codes....
are you in USA? if yes, then all scan tools work, here. for ECU.

The FSM has over 100 pages on , on car tranny diagnosis
ever seen that?

page 178 , see that, page? below. why not burn this to CD or memory stick and put it back in the glove box for next time.?

http://justgivemethedamnmanual.com/honda/honda-accord-owners-manuals/

FSM?
honda sells it.
see alldata dot com, or mitchels.
used FSM on fleabay ,dirt cheap.
or?

and OBD2 scan tool is like $9 today 2013
and this car has 100s of DTCs for just the tranny
P07xx 8xx and 9xx, one of the largest set of code of any car ever made, it blows the mind, how many.;
so connect the tool and see the codes.
DTC's diagnostic trouble codes.

Oct 11, 2013 | 2005 Honda Accord

2 Answers

Engin light stays on


The ECM has detected a fault in one or more of its systems. Go here,
extreme-check-engine-light-codes.com
and it will explain what to do to extract any codes that are stored.
Come back here with the code(s) and I can try and help further.

Oct 11, 2011 | 1993 Honda Accord

1 Answer

My 1986 honda accord lxi is giving me a code 13 WHAT is this code my pmg fi light on dash is coming on and RPMS are going up


Code 13 Barametric pressure sensor. ECM uses it for fuel mixture and timing.It is a wht 3-pin harness connector Baro-sensor is located under dash on passenger side make sure if there is a hose that it is attatch other than that you need this sensor

Apr 21, 2011 | 1986 Honda Accord

2 Answers

Need to find obd in 1990 honda accord


TROUBLE CODES System Diagnosis READING CODES When the "Check Engine'' warning light on the dashboard comes on and stays on, it indicates a problem in the fuel injection/emissions system. Check the ECU for fault codes. On certain models, some codes will not trigger the check engine light; if driveability has suffered, check for stored fault codes. The most common error when using fault codes is to assume the indicated component has failed rather than checking the entire circuit. The presence of a trouble code means simply that the electrical circuit for the named component is not functioning properly. For example, a code for the oxygen sensor circuit does not automatically mean the oxygen sensor has failed. A wire terminal may simply be loose or corroded at the connector. When using diagnostic or fault codes, always remember that the entire circuit including the component must be checked carefully. On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14). Fig. 7: Fault codes are read from the check engine light on most late-model vehicles 86804048.gif
Fig. 8: On Accords, the service connector is located under the dash on the passenger side 86804049.gif
Fig. 9: The service connector on Preludes is located behind the center console 86804050.gif
  1. Use a jumper wire to connect the two terminals of the service connector together.
  2. Turn the ignition switch ON; the check engine light will display any stored codes by rhythmic flashing. NOTE: In the event that a code is encountered which is not on the chart, re-count the number of flashes. If the code is truly wrong, it will be necessary to swap the ECU for a known-good unit and recheck. Since this can be expensive, you may wish to bring the car to a reputable repair facility if no other cause of the failure can be found. This may save you the expense of purchasing an unnecessary part.
  3. If no codes are displayed but a driveablity problem exits, testing of the system individual components is necessary to find the problem. If codes are displayed, follow the appropriate troubleshooting chart in this section. Fig. 10: Fault code chart for 1990-93 Accords 86804051.gif
    Fig. 11: Fault code chart for 1994-95 Accords (four cylinder) 86804052.gif
    Fig. 12: Fault code chart for 1992-95 Preludes 86804053.gif

Dec 14, 2010 | 1990 Honda Accord

2 Answers

1993 Honda Accord transmission problems


Need a scanner ,read the codes , do what the shop manual tells you to do regarding testing and repair.
Gonna take a guess cruse control and tach problems probably a wheel sensor possible the ecu.

Jun 09, 2009 | 1993 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...