Question about 1995 Mercury Sable

2 Answers

Trying to replace the rear window in a 1995 Mercury Sable. The problem we have is the window is glued in (from the factory) and we are having a hard time breaking the seal and lifting the window out of a junked car. Is there a way to dissolve the glue or cut through it?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Aut glass technicians use a 110 volt heated blade to remove the glass. Other wise its nearly impossible to get out

Posted on Jul 03, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just took a back window out of a 91 Sable at Pick-n-Pull yesterday. It was a bugger to do but we got it out without breaking the window. Forget about saving the seals. You have to cut them all. The car I am working on has a three-part rear window. A center part and separate curved pieces on each end. The piece I took out was the center.
At the top, remove the trip strip with the chrome trim. Cut it lose and chuck it. Then, take a thin bladed but sturdy knife, aim it down and toward the front of the car and cut using several passes, through the remaining seal all the was across. You won\'t be able to get the entire corner until you have the sides cut lose. Then you have to have someone push out at the corner while you use your knife to cut the corners lose. You can make progress a little at a time until you get through.
Be patient and don\'t push hard out hard on the window until it moves freely. After working for an hour or more to get it lose you don\'t want to break it.
To do the sides of the center window, lift the outside edge of the black trim strip, insert your knife and carefully cut through the trim from top to bottom. When you have to outside part off you have to get the rest out. Take your knife in a straight in position up against the glass, push in and cut the rubber from top to bottom. Remove the strip you cut off. Then, take your knife and angle it in under the glass and cut making several passes until you have cut through the seal. Do the same on the other side.
Along the bottom, open the trunk lid, cut under the seal towards the interior of the car as deep as you can get. Cut it all the way across. Shut the trunk lid and cut off the part of seal that overlaps the glass. Then, cut down along the edge of the glass as deep as you can go. Remove the rest of the seal.
At this point you should have the glass lose along the sides and at the top. If you didn\'t before, you need to have someone push out the top corners, carefully, so you can cut the adhesive lose. When the top and sides are free and you can easily push the top out you are ready to cut the bottom lose from the inside.
Have someone hold the top out a few inches so you can cut along the inside bottom until you have cut through far enough to loosen up the window and you can remove it.
Patience and perseverance are needed and it will take you a couple of hours to get it done. Hopefully, it won\'t be sunny and hotter than blazes when you do it. It was when we got ours and it was not a fun experience.
Good luck!

Posted on Aug 04, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My key won't turn to start my car... It's a 92 Sable Mercury.


Try a lubricant.

Mercury Sable key ? Mile High Locksmith ™

www.denver-locksmith.net/2013/12/mercury-sable-key-replacement/
Dec 23, 2013 - Mercury Sable keys have changed over the years. ... 1991, 1992, 1993, 1994, or 1995, then your car requires two keys. ... If your Mercury Sable was made in the year 1997, then some of the cars will have a transponder key, and some won't. ...Insert the new key into your ignition switch and turn it to the on .

Sep 08, 2015 | Mercury Sable Cars & Trucks

1 Answer

1995 mercury sable a/c fly wheel is frozen. car will start but belt smokes on unit. repair guy said it was a fuse, but checkd fuses and all are good. this happend overnight and not sure how to correct...


on a 95 its probably just worn out. try turning it with your hand. if you can do so easily its probably good. if not check your local salvage yard.

Jan 17, 2011 | 1995 Mercury Sable

1 Answer

I have a 1995 sable and the speedo quit and down shifts hard any ideas


Probably the speed sensor on the tranny, but may be the gears inside. The part is only $20 and a quick do it yourself, so I recommend replacing it to see if that does it. If not, you're into the tranny to fix little nylon gears, etc. Please let me know if you have questions.


jturcotte_159.gif

Nov 14, 2010 | 1995 Mercury Sable

2 Answers

How do u bleed brakes on 1995 mercury sable?cannot get them bled all the way.Would it have anything to do with the proportioning valve?


yes, if you are trying to bleed the back lines the proportioning valve can possibly reduce pressure to the rear. Are you pumping up the pedal to bleed? In this car, the recommended procedure is to start with the pedal up, open the bleeder, push the pedal down, close the bleeder, allow the pedal to retract, wait 5 seconds, repeat. OK?

Oct 03, 2010 | 1995 Mercury Sable

2 Answers

Where is the ignition control module located on a 1995 mercury sable 3.0 v6


For 1995 Mercury Sable 3.0L EFI 6cyl the Control Module-Ignition is located: Under hood, center, upper engine area, mounted on side of distributor.

Hope helps (remember rated this).

Aug 11, 2010 | 1995 Mercury Sable

1 Answer

1995 Mercury Sable driver's door mirror broken


You can get the glass from you friendly neighborhood junk yard and it should snap right in!

Jan 05, 2009 | 1995 Mercury Sable

1 Answer

Replacing water pump on 1995 mercury sable


water pump seems to be working but not pumping could it be a blockage?

Dec 09, 2008 | 1995 Mercury Sable

Not finding what you are looking for?
1995 Mercury Sable Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...