Question about 1998 Plymouth Breeze

Open Question

What sequence for bleeding brakes on a 1998 plymouth breeze?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: How do I change the

look around the power steering pump, (Under or maybe behind) you should see a belt tensioner, loosen it and any other brackets close to that have a sliding point, once loose, the belt should slip right6 off, pay close attichion to the way it comes off, you don't wanna put it back on backwards, or your water pump will run in the wrong direction and cause it to over heat

Posted on Jan 08, 2009

Ad
  • 3600 Answers

SOURCE: 1998 plymouth breeze left rear brake stays on

Your E-brake cable needs a to be loosened up and you need to see if the E. Brake is locking up, if the cable is not frayed then you have a problem with a check valve in the master cylinder or in the T where the line goes to the left and right. If you want to know how to check out the hydraulic problem it is more detailed, but first you must make sure that the mechanical part is not binding up.

Posted on Jun 15, 2009

  • 523 Answers

SOURCE: 1998 plymouth breeze is hard to steer. The power

I would expect teither the power steering pump or the steering rack has failed. The good fluid in the unit is just not being put to use.
I hope this may have helped,
Tom

Posted on Oct 27, 2009

  • 245 Answers

SOURCE: 1998 Plymouth Breeze, heater does not blow warm

Check your coolant level. Replace your thermostat and flush coolant system. If you bought used and it never has worked, make sure that the heater core has not been bypassed. If it has, it will probably have to be replaced(was probably leaking on previous owner)

Posted on Feb 19, 2010

  • 236 Answers

SOURCE: my brakes go to the floor and i need to know the

always start with the back passenger wheel, then back drivers wheel, then front passenger, last front drivers wheel, there should be a bleeder valve on each caliper, probably a 3/8 or 5/16 open end wrench, have someone pump the brakes up tight and hold it, turn the bleeder valve open until the pedal goes to the floor and retighten before they let the pedal go or it will **** air back in, continue doing this until you get a stream of fluid, no bubbles should be in the fluid, dont forget to keep adding a little bit of brake fluid every so often during bleeding

Posted on Jan 21, 2011

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights are not working on 1998 Plymouth breeze


check brake light switch. you should have power all the time on one wire and only power on the 2nd wire when the brake pedal is pushed. if you have this check the bulbs and then the sockets for power and ground. if you have power through the switch and none at the sockets you have a break in the wire for the brake circuit that you will have to find and repair. the wires run on the drivers side under the carpet.

Mar 01, 2015 | 1998 Plymouth Breeze

1 Answer

2008 ply breeze 2.0 no vacum at brake boostor or pvc


Start at the booster & pcv & work your way back
to the vacuum source.

Apr 25, 2014 | 1998 Plymouth Breeze

2 Answers

Where is the brake light switch on a 1998 plymouth breeze


1998 Plymouth breeze all Light are working except the right Break Light

Jun 04, 2012 | 1999 Plymouth Breeze

1 Answer

My 98 Plymouth Breeze stalls when I hit the brakes or turn a corner,or anything else that jars the engine.


does it stall only when you hit the brakes ? If Yes then it could be your Torque coverter lockup soloniod. I f you ahve automatic transmission. But if it stalls beside barking then somthing else is wrong.

Dec 05, 2010 | 1998 Plymouth Breeze

1 Answer

1998 Plymouth Breeze brake panel light - what does it mean? No owner's manual in car.


the brake light illuminated on the dash will indicate that either the emergency brake is on, the brake fluid is low, or there is a problem with the brake system. Make sure the e-brake is off. If the pedal feels normal check the fluid level in the reservoir. If its low add fresh BRAKE fluid from a new sealed container.

Nov 29, 2010 | 1998 Plymouth Breeze

1 Answer

We need the cylinder head torque specks for a 2.4 liter engine on a 98 plymouth breeze


f866f0c.jpg

Fig. 1: Cylinder head bolt tightening sequence-2.0L SOHC engine



f8b64c8.jpg

Fig. 2: Cylinder head bolt tightening sequence-2.0L and 2.4L DOHC engines

Tighten the bolts in 4 steps as follows:
a. First: all bolts to 25 ft. lbs. (34 Nm).

b. Second: all bolts to 50 ft. lbs. (68 Nm).

c. Third: all bolts again to 50 ft. lbs. (68 Nm).
d. Fourth: all bolts an additional 1 / 4 turn.

Do not use a torque wrench for the fourth step.


Hope helps (remember to rate and comment this).

Oct 22, 2010 | 1998 Plymouth Breeze

1 Answer

Put on new disc on front, can't seem to get brakes to bleede air.


u need need to have a shop bleed these brakes, there is a special tool for the ABS system that holds open the tiny popit valves in the ABS hydraulic control unit and allows air to bleed by. There is no way areound this, the job is not that expensive, any time shop can do it.

May 30, 2010 | 1998 Plymouth Breeze

1 Answer

What is the sequence when bleeding brakes -is it front to rear or rear to front


start at the furthest wheel to the nearst, so rr,lr,rf lf, good luck

Apr 17, 2010 | 1998 Plymouth Breeze

3 Answers

1998 plymouth breeze left rear brake stays on


Your E-brake cable needs a to be loosened up and you need to see if the E. Brake is locking up, if the cable is not frayed then you have a problem with a check valve in the master cylinder or in the T where the line goes to the left and right. If you want to know how to check out the hydraulic problem it is more detailed, but first you must make sure that the mechanical part is not binding up.

Jun 15, 2009 | 1997 Plymouth Breeze

Not finding what you are looking for?
1998 Plymouth Breeze Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...