Question about 1993 Dodge Grand Caravan

1 Answer

Is there a part on the firewall which helps the transmisson

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 229 Answers

I can't think of anything specific, except for the kick down cable passes through a grommet in the firewall. That controls the shifter lever to the tranny.

There are wireharnesses that pass through the firewall that goto the Junction box and ECUs under the dash.

Posted on Jul 03, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to check the transmisson fluid on a dodge journey sxt 2009

Hi, I will assume this vehicle has an automatic transmision, and a transverse mounted engine. If this is the case the transmision dipstick will usually be located under the hood on the passenger side of the car,
between the engine/trans. and the firewall. Some are on the drivers side based on exactly which drive train is in the vehicle. It will also usually say trans or something similar on it.This should be checked when the vehicle is hot running, in Park and on a level surface.
Hope this helps Vern

Jan 31, 2012 | 2009 Dodge Journey

1 Answer

Clunking when i take off

sounds like a broken transmission mount, get a pry bar and stick it over the transmisson crossmember but under the transmisson and try to pry the transmisson upward, if it moves up and down replace the transmisson mount, if this isnt the problem my next guess would be the driveshaft u-joints, grab the driveshaft near the rear end and turn it back and forth to check for excessive play

Jan 14, 2011 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

Where is the transmisson dip stick?

There very likley isn't A dip stick.
A transaxle is sealed , must be done by service tec.

Dec 30, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Clutch is stuck to the floor and will not go into

master cylinder low on brake fluid or it is bad or a bad slave cylinder, look for signs of leakage on the firewall, it it leaks on the firewall its bad if it's on the transmisson it would be the slave. if the clutch master cylinder is full then it is most likely the master cylinder.

Nov 11, 2009 | 2002 Saturn L-Series

1 Answer

After warm up the transmission will not always shift up into Drive and overdrive causing the engine to race.

try checking the fluid level if it is even aa half pint off it can cause shift problems, if it is low add some Lucas transmisson oil condtioner this will help it shift smoother. also look at the color of the fluid is it brownish in color? if yes then it's time to change the filter and fluid. if you take it to a shop they chagre about $150.00 but it will keep you from damaging the transmisson. the oil and filter for the transmisson should be changed every 30,000 miles on any car. Thisis oone of the most overlooked items of maintence on cars peopel simply don't know about change the filter and oil till they have to pay for a new transmisson.

Nov 09, 2009 | 2003 Jeep Grand Cherokee

1 Answer

Transmisson how do put transmisson fluid in a volov1986 gle740

The trans fluid goes down the tube that has the trans dipstick in it.A firm fitting hose,funnel and a bit of patience is needed to refill.The fluid does drain in slowly.Hope this helps

Aug 29, 2009 | 1986 Volvo 740

1 Answer

The flex plate cracked on my 1995 grand am.having problems splitting the engine from the transmisson

There is a bellhousing bolt that goes through the engine block and screws into bellhousing. You will need a long extension (2 to 3 feet) and an 18mm wobble socket to get to it. It is located on the firewall side of engine. Remove right side tire and using long extension and wobble socket you can get to it through the right fenderwell. Some GM cars have 2 bolts you have to get this way, one is right above the other one. Also, don't foget the torque converter bolts. Good luck. Hope this helps.

May 25, 2009 | 1997 Buick Skylark

1 Answer

Transmisson overdrive

does your truck have an od on/off switch?if so its bad.if not you have an overdrive solenoid on trans that is going bad.GinoR

Mar 22, 2009 | 1991 Ford Ranger Supercab

1 Answer


Chryslers need clean transmisson fuild and the right type of fuild. I would check the transmisson fuild level and top up if needed. If the fuild looks old and dirty have the transmisson serviced witha fuild and filter change - 50-100 buck could save you big $$$ on a trans job later

Nov 20, 2008 | 2001 Chrysler Sebring

1 Answer

1994 ford aspire

The speedometer sending unit is the filler port for the Manual transmission. Follow the speedometer cable from the firewall to the transmission and your there.

Jun 28, 2008 | 1994 Ford Aspire

Not finding what you are looking for?
1993 Dodge Grand Caravan Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides